ZMANALEX

One stop shop: Alex.

PM and payment received: All now sorted. Alex.

Plenty in stock and I supply them with my new compression rods (banana arm) but can be bought separately. YOU CAN NOT RUN WITH OUT THIS PART FITTED Surely the garage did not allow you to drive away with this part missing: :scare: Here is the link to my 10 page sub forum - Zstore where you will find all this stuff and much more: http://www.350z-uk.com/forum/137-zmanalex/page__prune_day__100__sort_by__Z-A__sort_key__last_post__topicfilter__all Compression Rods: http://www.350z-uk.com/topic/41839-new-genuine-nissan-compression-arms-banana/ Compression rod seats and nuts: http://www.350z-uk.com/topic/54898-compression-rod-ball-joint-nuts-and-seating-cones/ All in stock and good to go same/next day: Alex.

Welcome to the forum and good luck with your project. Unfortunately as you will soon find out it will cost more than your £400.00 budget to fix this car properly. I will have all the parts and panels in stock that you will require and once you have compiled a list of parts needed then just drop me a pm if you think that I can help you further. Alex.

Nice one Doogy: Plenty preowned cats in stock and good to go same next day: Just drop me a PM if I can help you further; Alex.

Nice one Doogy: Plenty in stock bluenose and good to go same/next day. Just drop me a pm if I can help you further. Alex.

Ping me over your reg. number by PM mate and I will price up for you. It is around a 2 hour job and a bit fiddly up in the pedal area, but hardly rocket science. Alex.

You may have to swop out the clutch master mate, however I suspect that there may be still some air in the system and would be worth another bleed before you splash the cash on a new master. Alex.

Remove the guess work and bite the bullet and get the car on Consult 3. Alex.

There is no easy way, and my preferred way is to remove the complete engine. All HR engine parts are in stock including valves etc. I also have complete cyl. heads with valves, buckets, cams etc which are ready just to drop on to the block I also have complete HR engines in stock and I can take your damaged engine back and give you an allowance.. Just drop me a PM if I can help you further: Alex.

Can't recall that conversation !!!!!! In stock and good to go same/next day if still required. Alex.

Unfortunately T1R in 245/45 18 is discontinued. Alex.

Thanks for the referrals guys: PM received and replied to. Various boot trim plastic sections in stock and good to go same/next day. Alex.

If fans okay then start with: Pressure cap. Air Lock: Thermostat: Blocked Radiator. Water pump. etc. etc. etc.

Best to take the car to a garage that knows there way around a 350Z. As the guys have said it could be that the electric fans are not kicking in, however this will only default when sitting stationery or in slow moving traffic. I have the fan motors and anything else that you may require to fix this issue in stock and good to go same/next day. Just drop me a PM if I can help you further even if it is for just a bit of technical guidance: Where are you based? Alex.

What reading are you getting off your oem gauge? Might be a plan to check the oil pressure directly off the engine. My defi used to warn me of low oil pressure on very low idle. Alex

Here you go Scotty: The link to my sub forum Z store where you will find all the service stuff and much more: http://www.350z-uk.com/forum/137-zmanalex/ The link to Motul 8100 Eco-Nergy 5w30. http://www.350z-uk.com/topic/66420-350z-engine-oil-service-kit-4695/ I can supply the oil with or without the filter: All in stock and good to go same/next day. Just drop me a PM if I can help you further. Alex.

Complete strut brace covers in stock with Z badge. Just drop me a PM if I can help further. Alex

Of course mate, I will pm them over shortly: Alex.

On your 2004 model, the slave cyl. is external and not part of the release bearing. The flywheel, clutch assembly and release bearing are all within the gearbox bell housing. The slave cyl. is bolted onto the outside of the gearbox. All the above parts including OEM dual mass flywheels, lightened single mass flywheels, clutch kits, release bearings, slave cyls and all fluids are in stock and good to go same/next day if required. You will find them all in my sub forum Z store. http://www.350z-uk.com/forum/137-zmanalex/page__prune_day__100__sort_by__Z-A__sort_key__last_post__topicfilter__all If you require any individual links or any further information then please do let me know. Alex

Pm received and replied to George: Alex.

PM received and replied to mate: Alex.

This is Thursday mate, isn't it ? or are you guys making me go :lol: Alex.

Here you go: http://www.350z-uk.com/topic/63753-boot-lid-release-assist-springs/ Alex.

In stock and good to go same/next day matey: You will find them in my Z store: http://www.350z-uk.com/forum/137-zmanalex/ Alex