ZMANALEX

Hi Jordan and welcome to the forum and congratulations on your new purchase. Where in the Highlands are you based? I am just down the A9 near Dunkeld just South of the Highlands. Alex.

Yes it is a DIY if you are handy with the tools and you have the correct tools and equipment to carry out the task. It is a 2 man job as the gearbox is heavy. Quite a few forum members have successfully fitted a new clutch and fly kit. Or you could pay a carefully selected garage circa £200.00 to do the work for you 350Z VQ35DE Clutch and fly kits are here if required: http://www.350z-uk.com/topic/63721-exedy-clutch-kits-27500-ultra-light-flys-34500/ In stock and good to go same/next day . Just drop me a PM if I can help you further. Alex.

Matt, As discussed by PM, I now only have one 350Z HR engine left in stock at the moment mate. Alex.

Aftermarket mats are usually tat, poor fit and quality and creap forward to under the pedals. This is what you need: http://www.350z-uk.com/topic/54882-floor-mat-sets-genuine-nissan-350z/ In stock and good to go same/next day. Alex.

Dan, 15 minutes to bleed the clutch hydraulics for the informed. 15 minutes to swop out the slave and line. 2 hours + to swop out the master. (I hate this job with a passion) Alex.

I can not offer you any " adivse" however i would recommend that you take your car to a 350Z specialist instead of a Nissan dealership. Where are you based and perhaps we can point you in the right direction. Alex

VQ35DE clutch kits are £275.00 and flys are £345.00 Labour is usually 4 hrs so budget for circa £200.00. Alex.

As above: Clutch kits here if you need them. http://www.350z-uk.com/topic/63721-exedy-clutch-kits-27500-ultra-light-flys-34500/ In stock and good to go same/next day. Alex.

After a while you will not even notice it. Alex.

It definately will not fit properly unless you replace the front arch liners with facelift liners. Also the headlamp washer stuff is all different and is not interchangable. Alex.

Nice one Paddy, thank you for the referral mate. As what Paddy has said. Swop out the slave and line and put some fresh fluid in and bleed properly and you should be sorted. If you are unlucky then you may require a master cyl as well but try the above first. All parts are in stock and good to go same/next day if required. Just drop me a PM if I can help further. Alex.

Martin, I think that the ECU picks up the temp signal from the temperature gauge sender, however I would have to consult the manual to give you an informed answer. Alex.

Julie, I can supply the genuine Nissan fan motors on there own or with fans, however most just swop the fans over. The Mishimoto fan surround comes complete with the shroud, fans and motors and represents great value at £180.00. All in stock and good to go same/next day if required. Alex.

There is no sender as such as the fans are controlled by the temperature settings within the ECU. These settings however can be changed to alter when the fans come on and go off. Alex.

Thank you for the referral guys: Alex.

New fan motor options here if required http://www.350z-uk.com/topic/46683-radiator-coolant-fan-motors-now-in-stock/ http://www.350z-uk.com/topic/66473-350z-mishimoto-performance-fan-shrouds-18000/ All in stock and good to go same/next day. Alex.

I have preowned rear JDM bumpers in stock. UK parking sensors whether genuine OEM or aftermarket can be fitted to the JDM rear bumper and will hook up to your wiring with no issues. Alex.

Arch liners are in stock for facelift and prefacelift. Alex.

The chain tensioners that I refer are inside the engine beside the chains. Alex.

Gates upgraded Blue Horizon belts and tensioner pulley nuts in stock and good to go same next day if required. http://www.350z-uk.com/topic/30394-350z-micro-v-new-style-gates-horizon-belts/ http://www.350z-uk.com/topic/54903-nuts-for-belt-tensioner-pulleys/ Alex.

Thank you Jay. PM received and replied to Vince: Huge choice of 350 and 370 rotors in stock and good to go same/next day. Alex.

Dan, New aluminium powdercoated here: http://www.350z-uk.com/topic/30380-alum-mesh-grills-powdercoated-now-with-clips/ Just drop me a PM if I can help further. Alex.

It is all stamped on the inside face. Alex.

Jez, 18" Rays are 8.0jj front and 8.5jj rear Offsets are 30 front and 33 rear. Alex.

Thank you for the referrals guys: PM on its way Ollie: All in stock and good to go same/next day. Alex.