Jump to content

Major JAAAAG project ...Update Feb 2018


leonk

Recommended Posts

Cheers Doogy.

Darren, definitely the way forward, now the shell can be taken on and off the dolly without worrying about the paint on the underside. I've also made it so that the full rear suspension and diff can be raised up into the painted shell while still on the dolly. The cross braces are removable for access too for fuel and brake lines etc. Just as a word of warning, I went for bigger wheels than the rotisserie as while great on the garage floor, loading it into the transporter and at the blasters was difficult. 350kg per wheel, braked, swivelling and with bearings all 4 for £65 delivered on ebay.

Thought that wasn't bad.

Link to comment
Share on other sites

  • 4 weeks later...

Another minor update. After much heartache and looking at all options, I came to the conclusion that the original bonnet was never going to be to my standard given the amount of damage it had to all the flanges. Added to this was damage done to it by the initial stripping company that they denied. The problem is that although very rigid as a complete bolted together bonnet, each individual panel is quite flimsey. This has marked a real low point in the restoration with the daunting prospect of having to shell out £7,000 on a new bonnet. When I'd given up all hope of finding a good secondhand one and looked at several that to me were only worth scrap, a guy on the Jag forum mentioned he was going to race his and was building a lightweight alloy panelled replica. A cheeky pm, a bit of haggling and a trip down to London with a Mercedes LWB Sprinter and I had a replacement bonnet from a US dry state car. I've started work on the bonnet, stripping it into its various components and then stripping them of paint. The smaller bits I can put in the blasting booth but the bigger panels have to be done by hand, The flat panels can't be blasted for fear of distorting them. It's a long and labour intensive job but at least I have some control of it this time.

 

Wooden dolly made to support the wings to work on them.

 

DSC_0626_zps6bnmrqrv.jpg

 

DSC_0627_zpshflm7j0t.jpg

 

 

And as if by magic....

 

DSC_0631_zpsixn8nvzh.jpg

 

DSC_0633_zpsbaujzccg.jpg

 

Bonnet centre section stripped and offered up. These were hand made and trimmed at the factory to fit each individual car. By the time of this photo it had already been on and off about 20 times and it's still not 100%. Going to have another go at the weekend when I'm in a better mood.

 

DSC_0629_zpsmtsl8yq2.jpg

Edited by leonk
Link to comment
Share on other sites

I do love your new front suspension arms mate - Black & Decker would be proud :lol:

Hang in there buddy you are doing a stirling job it's gonna be the nuts when finished :thumbs:

 

I may even have to make a road trip one weekend just to see this for myself ;)

  • Like 1
Link to comment
Share on other sites

  • 5 months later...

Funnily enough I've just come in from the garage . Unfortunately due to work commitments I've not really had much chance to work on the car. It's now off the rotisserie and onto the dolly I made. I'm back on it now though and hoping to get the new engine frames on next weekend. That means I can start offering the bonnet up. The bonnet then needs to be made to fit the car by means of shims and if necessary trimming the metal on the back edge to fit the bulkhead. As this is going to have to come on and off about 50 times to do this I'm making some sort of jig in order to minimise the chance of damage.

 

Overall I'm dreading it!! Haha. It will either fit or I'm into 8k for another bonnet and still no guarantee that will fit any better.

Think positive..... It WILL fit.

 

Hopefully some pics next weekend and thanks for asking and bearing with me.

  • Like 1
Link to comment
Share on other sites

Actually managed a bit more on the bonnet.

The main tub is off the rotisserie and onto the dolly I made. This allowed me access to the bulkhead ready for priming

priming

 

DSC_1192_zpsfhmlfmpx.jpg

I then concentrated on the bonnet jig given that it's going to need removing qnd refitting heaven knows how many times.

Notice the new bumper bar, all part of a cunning plan

plan...

Edited by leonk
  • Like 2
Link to comment
Share on other sites

You are putting as much work into fabricating jigs, stands and holders as you are the rebuild - Hats off to the dedication mate.

 

I recon you will have that bonnet lined up 2nd attempt (well fingers crossed) ;)

 

Keep up the good work :thumbs:

  • Like 2
Link to comment
Share on other sites

Thanks for the support and encouragement guys.

 

Keyser, ref all the jigs and stuff, you know the saying, All the gear and no idea..haha

 

Marzman, that bl##dy bonnet has given me "shivers" but not the nice ones! And it's not over yet.

 

Doogy. It's a bonnet, always has been always will be. Hood is somewhere you live...

 

Once again thanks for bearing with me, I know it's not the fastest of projects.

Next step is getting the new engine frames bolted on.

  • Like 3
Link to comment
Share on other sites

  • 4 weeks later...

Let's just say the bonnet to car alignment is as anticipated a little challenging! I've learnt that sometimes you have to step away from the project and return when you are in a better frame of mind. So hopefully after a little break I'll be back on it this weekend! What really really annoys me is that I had a perfectly fitting rust free original bonnet that complete muppets destroyed while stripping it. I have to try very hard not to keep thinking about this and start again.

Link to comment
Share on other sites

On a serious note, one of the things the seminar did highlight was the dangers of the new green trend of adding ethanol to petrol. this is something the government has signed up to as part of an EU initiative.

 

The problem is the damage this stuff does to your engine and fuel system, especially to older cars. From what I could gather from the talk, was that ethanol absorbs water and becomes highly corrosive. One guy there in the questions and answers section at the end who worked in the fuel industry said that they delay putting the stuff in the tankers as long as possible because of the damage it causes. One of the lecturers warned that they were seeing more and more cases of expensive fuel systems and carbs destroyed by the fuel especially in cars stood for any amount of time. He pointed out an example of a V12 Jaguar that it had caused nearly 10k worth of damage to. :scare:

The only answer to it at the moment seems to be to completely drain down the fuel system if the car is not used.

 

Now not only do I have to worry about the humidity and rust but the bl**dy government conspiring to destroy my car! :surrender::lol:

 

You know which way to vote if we ever get the chance then ;)

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...