ZMANALEX

Congratulations Dave

Nice one Carl Superb gesture, again demonstrating what this forum is all about.

Mark, the OP was asking about power gains. and I did not say that he would not be happy.

Hi Lewis and welcome to the forum There are many 350Z and forum members in Aberdeen and the Shire and I am sure that they will be along shortly to welcome you. I am in the Perth area so you pass my neck of the woods every week, whether you drive or fly. Alex.

Hi and welcome to the forum You can not chip the VQ35DE but you can certainly remap. There are various ways that you can do this but one of the most cost effective engine management solutions is the Uprev using the Osiris software. If you are planning to remain N/A then only nominal bhp gains will be achievable. If you long for substantial power gains then you will have to go down the FI route. Alex.

Providing you are referring to the stop/tail light within the rear tail lamp assembly and not the high level lamp, then it is only a standard bayonet type bulb that you require, 12v 21/5w double filament. What Halfords were probably trying to give you was more than likely a standard stop tail 380 bulb. Most motor factors or garages will have these readily available as they are a standard fitment throughout the motor industry and they are not 350Z specific

Jez, PMs received and replied to mate

If people are happy then that's all that matters All Rich and I said was, it's cheap (which it is) and that it isn't reversible (which it isn't) I would never tell someone not to do this or that just that I don't like it I personally don't want chicken wire on my Zed, it belongs on Corsas and Saxos, 2 of my mates on here have you mesh and are more than happy with how it looks so fair play It's a forum at the end of the day and if everyone only posted what they like it would be boring The nismo front end comes out the factory with the mesh..... Yip, and if it is good enough for Nismo then it is good enough for me.

To all you Zmanalex mesh bashers Over the past 18 months I have sold on various forums over 550 universal Allumium mesh panels powder coated predominantly in black. I have also sold over 300 on eBay during the same period. 100% feedback and absolutely no complaints. 850 peeps can not be wrong.

Welcome to the forum

viewtopic.php?f=157&t=31534

Your list is comprehensive Craig, however a new crush washer would not go amiss. As you know all in stock Alex.

I can supply the pipe in meter lengths Daryl, but if it is for the brakes then best to do both sides mate. Drop me a pm if you want to discuss further.

Welcome to the forum Your knock could be numerous things but the most probable will be the compression arm bush. viewtopic.php?f=157&t=43455 viewtopic.php?f=157&t=43456 Just drop me a pm if I can help you further Alex.

If you are unfortunate enough to require a gearbox mate, then I have five preowned low milage 6 speed boxes in stock. New Exedy Clutch Kits and Fidanza aluminium single mass lightened flywheels all in stock together with OEM dual mass flywheels if you wish to remain stock. Have a look in my sub-forum for prices All in stock and good to go same/next day. viewforum.php?f=157 Just if you want further help or advice.

Sorry to bump this but did it ever get an answer? Would like to do the same myself and there is enough out there with scrappies. I guess the question is can you uk model heated seats in a non GT spec car? A straight forward upgrade, with no drama

Chris, I have a spare brand new (sealed) Haynes manual for the 350Z/Infiniti G35 2003-2008 based on a complete teardown and rebuild. I have one of these myself in the workshop and it is full of useful information. £20.00 shipped mate Alex.

I can offer you these viewtopic.php?f=157&t=42415

As Zugara says. If you are going to meddle with the horn push then watch and not deploy the air bag

If you require a new Maf sensor then here you go. viewtopic.php?f=157&t=43467 viewtopic.php?f=157&t=43466 Just pm if I can help you further

I think it will work but I believe that the mods require a bit of time to approve your listing.

Steve, I have a preowned cooler, lines and connectors in stock if of interest to you. I also have a thermostatic sandwich plate as well mate. Drop me a pm if I can help you further. Alex.

Unfortunately the grease and rotate method is only a temporary fix

Just let nature take its course and let it thaw out. Give it a good road test or give the battery a boost. The above should fix your issues

Here you go mate. Plenty in stock and very happy to talk you through your fitment issues viewtopic.php?f=157&t=43453 Alex.