Jump to content

ZMANALEX

Members
 View Profile  See their activity

  • Posts

    14,789

  • Joined

  • Last visited

 Content Type 

Everything posted by ZMANALEX

  1. ZMANALEX
    I can let you have a pair of new front Brembo style discs which are OEM quality and Ferodo or Mintex pads for £150.00. As Rabbitstew has said very easy as a DIY or supply your own parts to the garage. Just drop me a PM if I can help further. Alex.
  2. ZMANALEX
    It wasn't just the light covering of snow that was the issue, but the ice rink underneath.
  3. ZMANALEX
    Was looking forward to this, however, was not meant to be.
  4. ZMANALEX
    All over the place this week, so Just drop me a PM when you are next in the area and I will try and be there for you.
  5. ZMANALEX
    Swing by and I will have a look at it for you.
  6. ZMANALEX
    In stock and good to go same/next day. Just drop me a PM if I can help further.
  7. ZMANALEX
    Belts will not be covered by your warranty, however, they should have been replaced before you took delivery of the car. Hopefully, you will get a goodwill.
  8. ZMANALEX
    John, Only one belt on this car and it is self adjusting. Check the notches on the self adjuster to determine if the belt is stretched. To eliminate the belt or pulleys, Just remove the belt (2 second job) and try your cold start with the belt off. Alex.
  9. ZMANALEX
    No, but you will have to remove parts of the dash if you wish to remove the A pillar trim completely. Could you not just partially remove (pop) the trim as I guess that you are just wanting to feed some wires/cabling down?
  10. ZMANALEX
    Afraid it is a bit more than that as the trim is hooked in at the bottom at the dash:
  11. ZMANALEX
    Gary, PM received and replied to, so guess that you must have figured it out.
  12. ZMANALEX
    Gary, I am just down the road from Blair as I am based near Dunkeld and my shop is in Balbeggie. Just drop me a PM and we can have a chat. Oh, and to the forum. Alex.
  13. ZMANALEX
    to the forum.
  14. ZMANALEX
    Worms will be fine providing your pipework has lips on the end. If your pipework does not have a lip, it is very easy just to run a stitch of weld around the end of the pipe or coupler.
  15. ZMANALEX
    You can try replacing the sensor, plenty in stock if required.
  16. ZMANALEX
    Providing there is not a bolt left in half screwed out then the box will probably just be sticking on the dowels. Rest the box on a tranny hydraulic jack and get a pry bar between the engine and the gearbox bell housing.
  17. ZMANALEX
    I have a low mileage Kazz 2 way which has just been removed from my 350Z. Plates all good and can be set at 60% - 80% or 100% lock. Side bearings are as new. Just drop me a PM if I can help further. Alex.
  18. ZMANALEX
    to the forum from another Roadster owner.
  19. ZMANALEX
    to the forum.
  20. ZMANALEX

    wanted

    ZMANALEX replied to leadman's topic in Wanted

    You have PM.
  21. ZMANALEX
    You are welcome. Happy to help
  22. ZMANALEX

    wanted

    ZMANALEX replied to leadman's topic in Wanted

    In stock and good to go same/next day. Just drop me a PM if I can help further. Alex.
  23. ZMANALEX
    PM received and replied to
  24. ZMANALEX
    In stock and good to go same/next day, just drop me a PM if I can help further.
  25. ZMANALEX
    PM received and replied to: Thanks for the referrals guys.
×
×
  • Create New...