Willsy1980

Just an update to this, the Stoptech pads are a great choice. Far less dust than the oem Brembo's I recently put on the front. Again, many thanks for the recommendation and the top service.

I'd stick with OEM unless you do all 4 corners, aftermarket rears and standard fronts would drive like crap. PM @ZMANALEX he will have some for you. Sorry Torqen, not meaning to redirect business or anything. Last thing I was trying to do.

Very nice ! Love those wheels.

Great write up and the results speak for themselves. As for the birds, skip buying a DA next purchase, a shotgun Another point on the blower, a small compressor and blow gun will work just as well at a fraction of the cost. http://www.ebay.co.uk/itm/SwitZer-Air-Compressor-50L-Litre-2-5HP-8-BAR-230V-9-6CFM-With-Wheel-AC001-Grey/122643181630?_trkparms=aid%3D555014%26algo%3DPL.DEFAULT%26ao%3D1%26asc%3D20170221124951%26meid%3D2befa87b039d423b9844f559f70623fa%26pid%3D100643%26rk%3D1%26rkt%3D1%26&_trksid=p2045573.c100643.m3226 Just add an inline pressure reg and blow gun and you're good to go

5600 in mine, so I can shift well before the limiter. No need to be bouncing off that on public roads

No worries, just any hole you can find near by, if the nozzle will fit, shove it in and spray is the best approach. Same for the car and waxoil

Id pop them out, there are a few additional holes you can attack from. I'd probably just remove the lights to start, there are some holes the locating pegs go in, remove the little bungs and fire it in there. These are not 100% for getting waxoil down all the way, but better than randomly drilling holes everywhere. That could lead to more issues than what you are trying to prevent if im honest.

If you remove the rear light clusters and fire a load in through the holes circled, it 'should' run down quite a bit. But you will need to dump loads in and just hope for the best.

Well, not today but yesterday added some mirror mods...

Surely these can be 3d printed at a fraction of that ?

It's a pity their beer is pish

I think the new look is better, one thing I would change is the technical section the first full page is stickies, maybe archive these down in a sub forum within tech ?

Many thanks again Adrian, Stoptech rear pads will be fitted tomorrow morning. I'll be back for the fronts soon and get rid of the OEM's

Does the car come with it ? Lovely Z

Spotted on the A500/50 this morning bit of a blur as to the time i'd been up since 5am, was in the Silver Kuga in front of you for a few miles ish, blew past as soon as it was clear

Sanded, cleaned and wrapped. Done a little more trimming since the photo, but you get the idea

It is better that 07 and 10 but im on 16 now, bit flashy but does everything you need

Hahaha, im surprised W10 even lets you install it. I'll agree it's better then 2003 but 2013 and 16 are actually pretty good

Is it that you are still using Office 2007 ?

May as well do the lot, inside the boot cavity and doors.

There appear to be 3 extra 0's on the end, surely that is a typo and should be £6590 ? Still over priced by about 6k

I play on PS4 with the T300 on a stand, works with the PC too. Good force feedback but in game set ups do need a lot of tweaking to get the best out of it, once you have the base settings dialed in then move on to the individual car FFB settings. You will spend more time setting things up than racing in the first few days

Also says 1.3 and 1.6 engine ? interesting 1.3 to power the front and a 1.6 rear, good power balance. But these figures... Power63 bhp Torque75 lbs/ft Top speed111 mph Acceleration0 to 62 in 11.1 secs Bit ambitious with a whopping 63 bhp :O

4 hours on a motorway, last thing you want is small and cheap. Diesel or petrol Focus would be a decent starting point, pick them up for peanuts and parts are cheap. Any MK2/2.5 will have all the features you need.

Hope that's a duff sensor or that is bad news....