ZMANALEX

Some 350s are known to rattle for a few seconds from cold start and there are numerous factors which might cause this. However if you have explored all the possibilities and the rattle is from the one of the cam chains, then I doubt if it will be the hydraulic tensioner and is more than likely to be one of the cam chains. This year alone I have replaced cam chains on two 350s due to similar issues. From cold, If you check how far the tensioner is protruding from the tensioner housing then that will give you an idea what is going on. Circa 10mm protrusion is acceptable and circa 20mm is not. If the protrusion is circa 20mm then the reason usually for this is that the small cam chain will be stretched and the tensioner has to come out further to take up the slack and the rattle you get is due to the chain interfering with the casing. If the above is your issue then a new cam chain and tensioner will fix your issue. Also best to replace the chain guides and slippers when you are at it as Nissan have upgraded these with more efficient and durable parts. Alex.

Afraid not mate.

Unfortunately the cam shaft has to be removed to get access to the bucket and valve spring. I would recommend that you run another compression check and also a cyl.leakage test. Alex.

As what Keyser has said: Plenty drop links and nuts in stock Kyle, and good to go same/next day. Alex.

Not rpm related so guess that something must be touching one of the pulleys. Alex.

:lol:

Clip on. Alex

If you are also looking for advice on what to fit to retain or improve on your present power levels then I would recommend that you retain the 06 airbox and fit a Performance Panel drop in filter. Cosworth or HKS are the most popular and both improve filtration and cold air intake. Plenty in stock and good to go same/next day. Just drop me a PM if I can help you further. http://www.350z-uk.com/topic/46565-hks-de-350z-performance-panel-filters/ http://www.350z-uk.com/topic/40448-cosworth-drop-in-panel-filter-vq35de/ And here is the link to my 10 page sub forum Z store where you will find all this stuff and much more. http://www.350z-uk.com/forum/137-zmanalex/page__prune_day__100__sort_by__Z-A__sort_key__last_post__topicfilter__all Alex.

One word: DEMENTIA :lol:

The fronts are completely different from the rears and they are definately not interchangable with the rears The rear links will not fit to the front and visa versa. The garage have messed up big style and they are at it. It is now down to them to fit the links that you supplied to the rear and provide links to the front free of charge of any cost whatsoever. Links in stock if required and good to go same/next day. Alex.

Nice one Doogy but Pete should already know that. Both HR parts are in stock and good to go same next day. Alex.

All in stock at the moment including the panels but not in GM. Drop me a PM if I can help you further: Alex.

Bank 2 is the L/H side and sensor 2 is the rear sensor. This should fix your issue if it is down to the HFCs. http://www.350z-uk.com/topic/23011-o2-simulatorslamda-spacers-to-fix-cel-dash-light/ In stock and good to go same/next day. Drop me a PM if I can help further. Alex.

As above, get a trolly jack or HUGE bar and force the ball joint and seating cone together, with a bit of brute force you should be able to "lock" the ball joint from spinning. All ball joints, seating cones, bushings, arms and nuts in stock if required. Alex.

As recommended above, P2 next: All parts in stock and good to go same/next day if required. Alex.

In stock and good to go same/next day if required: http://www.350z-uk.com/topic/54916-cam-rocker-covers-for-350z/ http://www.350z-uk.com/topic/46544-genuine-nissan-cam-box-gaskets/ Alex

Thank you Will: In stock and good to go same/next day. But be warned there is no such thing as a cheap fully working Xenon headlamp with all electrics and fixing brackets intact. Alex.

Hi and welcome to the forum, why don't you put up an intro post to introduce your self. I am rushing out for some track fun at the moment so don't have the time to give you accurate informed answers to your questions. However the control unit is under the dash close to the steering column and will start with part code 47851 and is manufactured by Bosch. I have plenty in stock if required. ABS sensors are also in stock. Alex

That plan is now up in the air thanks to Kyle R. Current stock: 1 x L/H 8 pin Xenon 2 x L/H 8 pin Bi Xenon Alex.

Niki, In stock and good to go same/next day. Alex.

Hi mate, the one that you bought did have the motor attached and also a wiring tail and connector to hook up to the loom. Alex.

Simples, get the car checked out properly for an informed diagnoses. Hopefully it will nof be to serious or expensive. I will have any parts that you may require in stock and good to go same/next day. In the meantime best to check your wheel nuts are tight. Alex.

This is a no brainer, go for an HR 313 for the same or less money. Alex.

PM received and replied to: Alex.

Azure coupe on A9 heading North 10 miles North of Perth 11.30 am today.