ZMANALEX

Thanks guys: PM received and replied to. Bulb holder on its way. Alex.

Superb looking 350 and good job well done. Alex.

Carsten, Genuine Nissan AT J Fluid in stock if required mate. Alex.

More than likely it will be the compression rod bushing or the compression rod ball joint. All parts are in stock and good to go same/next day. Just drop me a PM if I can help you further with your diagnoses. Alex.

If Keyser can not help then I have JDM preowned calipers in stock. I also have 20" tyres and wheel nuts. Alex.

Should possibly have a mint OEM front prefacelift silver bumper in stock tomorrow. Alex.

Thank you 14N. OP: Just drop me a PM if I can help you further; Brembo front and rear shims in stock and good to go same/next day. Alex.

:headhurt:

Yes, the front and rear screen washer will work fine as the L/H bottle is fed from the R/H bottle. Alex.

Steve, With most of these FI upgrades the L/H bottle for the headlamp washer has to be removed. Just blank off the pipes and all will be well until MOT time. Alex.

Matt, It is in the IPDM at the battery. It is the 4th one down on the right and rated at 10 amps. Alex.

Saskhi, Plenty preowned oem plenum bolts in stock if required. Might even have the longer ones for the spacer, but I would have to check. Just swing by next time you are passing, Alex.

You have PM dakes. Alex.

OK one more time: CHECK THE AIR BAG CONNECTIONS BELOW THE PASSENGER SEAT. THEN CARRY OUT THE AIR BAG RESET. If you are still having issues send me over the fault code if there is one stored. Alex.

What part of "Your car is not equipped with a front crash sensor." do you not understand ? I have also told you that I would require a code for me to help you further Now you are telling me that you have an air bag light on. Have you checked the connections below the passenger seat ? Have you carried out the airbag reset? Alex.

Seabee, I have already told you by PM this morning that the picture is of your ambient air temperature sensor. Your car is not equipped with a front crash sensor. Why are you finding it so difficult to take this on board: :lol: Alex.

The upgraded parts only apply if you are buying replacement parts. All the original VQ35DE motors will have the original design as far as I know. Nissan applied the change with a superceded part number circa 18 months ago. Alex.

There appears to be no pattern (mileage or time) to this issue but Nissan have upgraded the chain slippers and guides so they do recognise that there is an issue but will never admit it. Although I have seen a few of these issues it is still quite rare and really my view is that you do not have a problem until you have a problem and no one should really be overly concerned about potential chain, slipper, guide or tensioner wear. Alex.

That certainly used to be the case Graham, however with these cars getting older and mileages creeping up, it now has become an issue that I have experienced more and more over the past few years. The chains have been known to stretch so much that the timing goes slightly out. I had one 4 weeks ago where one of the hydraulic tensioners was fully extended and the chain was rattling off the casing. Fortunately this is an exception rather than the rule but still a worrying issue. OP: best to let a 350Z engine specialist have a listen to it for an informed diagnoses before you start pulling the motor. Alex.

The clutch release bearing is not turning until you press the clutch pedal so the noise will not be from the bearing. The noise you describe sounds like it is from the DMF. Usually the DMF is only replaced when you swop out the clutch kit unless you have a complete DMF failure which is highly unlikely. Alex.

Clutch and fly kits are here if required. In stock and good to go same/next day: http://www.350z-uk.com/topic/63721-exedy-clutch-kits-27500-ultra-light-flys-34500/ http://www.350z-uk.com/topic/63723-dual-mass-flywheels-350z-vq35de/ Alex

I have two that I am dismantling at the moment, both 2005. Alex

PM received and replied to: Alex

Cosworth and HKS Performance Panel Filters for 370 are both in stock and good to go same/next day. These appear to be the two favourites for the 350 HR and 370 HR dual intake. Just drop me a PM if I can help you further: Alex.

Dean, Clutch and fly combos here: http://www.350z-uk.com/topic/63721-exedy-clutch-kits-27500-ultra-light-flys-34500/ Dual mass flywheels here: http://www.350z-uk.com/topic/63723-dual-mass-flywheels-350z-vq35de/ Just give me a shout if I can help further. Alex.