evilscorp

Was a carbon cover thing for the middle bit the previous owner put on with too much tiger seal. fingers are blistered after removing it with a hair dryer. Here is how much tiger seal I applied for the canards. spirit gauge was useless One side went on quite easy, the other was a little tricky, slight different angle on it so took a few attempts and some mole grips to get the angle right. Note, use lots of masking tape and wait till its rubber like consistency before using your nails or something to push/scrape off any over squidge(cant think of the right term). excuse the masking tape as its for the lip tomorrow.

Obviously he does gymnastics in his spare time.... dressed as a cat.

Test fitting of the new canards and GT lip from Tarmac. Low down close together or large gap?

Here are a few, posted the ones with the GT lip and outside the garage on my thread (shameless plug) scream if you want to go faster

Tiger seal has arrived, but going to use double sided tape to check positioning for best look/function. Have taken a few photos of the bumper off with the new lip and canards but will offer it up to the car so people can get an idea. Excuse the old tiger seal on the oem bumper lip there was a carbon cover on it before which is now destined for the bin I think.

Waiting for mine to arrive, bumper is off and will fit gt lip this week along with the carbon canards. Will post pics when done.

Get Q division to hurry things up!

Looks nearly finished to me? Not Much of a project with such a nice car!

Hey Kev. That's interesting — are these off the shelf products or custom fabricated? If the former, where are they from. I'd like to find out more about this (to satisfy my own nerdy curiosity!) http://www.tarmacsportz.co.uk/GB/370z_Zspeed_Aluminum_Undertrays/370ZSPUT_.aspx

Bargain! The build detail was outstanding on this car, someone is going to be very lucky/happy owner . . . . . (Once they change the colour =p )

full mailbox?

I presume it's a DE rev -up you have at the moment?

Hope you have enough fuel to get where you are going, seen you stop at Tesco kilburnie to the disappointment of no super, followed you down in my white I10 sounds like a nice aftermarket exhaust, what is it?

it's missing the x pipe section, should be longer I think. Can't remember how the pipes connect to the x pipe section but that has no flanges.

Its not the same as my DC sports exhaust, must be an old, old version or fake? mine has a x over.

Mines not all set up yet but this is how I was going to do my set up; On the passenger side I was going to put a mini breather filter. On the drivers side I was going to take the pipe from the crank case to the oil catch can, then take the pipe from the exit side of the oil catch can to the plenum with a non return check valve inline to stop pressure from the plenum going backwards towards the oil catch can/crank case. Same for me but have not drilled out the oem pcv valve. I have to empty my rutland motors catch tank every 3-4 long drives as it fills up quite fast.

Looks good, but prefer garage mak widebody kit if only it was £4k lol.

Mine should arrive tomorrow, after a delay from customs =/

Lovely =) if only I had less sense. Think you are becoming like Ian. Lol

I will take them off you =)

30mins work + some grease. £40?

If your boosting, it means you have balls! (And a back up fund for when it goes pop!)

Happy for you mate, with all the hassle in the past. Onwards and upwards (faster)! Enjoy, I give you till next year before you want more lol.

Got a seibon bonnet, got bonnet pins, but been driving about for couple of years with them sitting in my cubby compartment =/ need to fit them soon, only reason I feel safe is that I don't do silly speeds or track much but having tried the drag strip I don't feel confident in the seibon latch alone. Just need the balls to drill the holes now.

Nothing stealthy about that snail!