ZMANALEX

Fitting spacers will not create a camber issue but it may highlight that there is an issue. Perhaps you have a bent suspension rear arm or more than likely the camber may just require adjustment. Get the car on a computerised 4 wheel alignment machine and have it checked out. The camber and toe adjustments on the rear are by 4 snail cams on the rear aluminium sub frame.

Well let's start here: That is if you need them. viewtopic.php?f=157&t=44399

There is no chatter with the ATS 1100kg CT. However, they do require proper bedding in and warming up.

Carbonetic and ATS are the same

Here you go mate viewtopic.php?f=157&t=43453

Alex, just out of curiosity, do you know what light I might have got then? It looks like I can trim up the plug to get it to fit, but it obviously requires different plugs that must be correct for some variant? Cheers, Chris. Hi Chris, There are a 4 variants of UK LED rear lamps and I would think that you have got one of these. 3 of the variants require the block connector to be trimmed. The 4th type which I supply fits all UK and all JDM models without trimming. Once you have trimmed to make it fit remember and wrap a bit of insulating tape round the block connector just to keep it nice and tight Alex.

Cheers Alex... if only I knew where the Control Unit was Haven't had any lights since Friday and used the car everyday... very strange Beside the brake servo Dave under the plastic cover where you are supposed to check your brake fluid on a regular basis.

It is on the control unit beside the servo.

The lights that I supply fit both UK and JDM without any modification

Lines, fluids, and rear calliper fixing bolts is all that you will require. Yes, they will fit into stock Nissan 350Z or G35 17" rims. I have all the above if you require them. Just if I can help you further. Alex.

And your point is.

Nice one Dave, thank you PMs received and replied to In stock and good to go same/next day Alex.

Congratulations Dave

Nice one Carl Superb gesture, again demonstrating what this forum is all about.

Mark, the OP was asking about power gains. and I did not say that he would not be happy.

Hi Lewis and welcome to the forum There are many 350Z and forum members in Aberdeen and the Shire and I am sure that they will be along shortly to welcome you. I am in the Perth area so you pass my neck of the woods every week, whether you drive or fly. Alex.

Hi and welcome to the forum You can not chip the VQ35DE but you can certainly remap. There are various ways that you can do this but one of the most cost effective engine management solutions is the Uprev using the Osiris software. If you are planning to remain N/A then only nominal bhp gains will be achievable. If you long for substantial power gains then you will have to go down the FI route. Alex.

Providing you are referring to the stop/tail light within the rear tail lamp assembly and not the high level lamp, then it is only a standard bayonet type bulb that you require, 12v 21/5w double filament. What Halfords were probably trying to give you was more than likely a standard stop tail 380 bulb. Most motor factors or garages will have these readily available as they are a standard fitment throughout the motor industry and they are not 350Z specific

Jez, PMs received and replied to mate

If people are happy then that's all that matters All Rich and I said was, it's cheap (which it is) and that it isn't reversible (which it isn't) I would never tell someone not to do this or that just that I don't like it I personally don't want chicken wire on my Zed, it belongs on Corsas and Saxos, 2 of my mates on here have you mesh and are more than happy with how it looks so fair play It's a forum at the end of the day and if everyone only posted what they like it would be boring The nismo front end comes out the factory with the mesh..... Yip, and if it is good enough for Nismo then it is good enough for me.

To all you Zmanalex mesh bashers Over the past 18 months I have sold on various forums over 550 universal Allumium mesh panels powder coated predominantly in black. I have also sold over 300 on eBay during the same period. 100% feedback and absolutely no complaints. 850 peeps can not be wrong.

Welcome to the forum

viewtopic.php?f=157&t=31534

Your list is comprehensive Craig, however a new crush washer would not go amiss. As you know all in stock Alex.

I can supply the pipe in meter lengths Daryl, but if it is for the brakes then best to do both sides mate. Drop me a pm if you want to discuss further.