ryzf Posted July 17, 2011 Posted July 17, 2011 Hi Everbody I am new to this forum and wondered whether you could offer me some help? I have a 2003 350Z and whilst driving it today the throttle went and I am only getting 1500 revs, please can anybody offer me any assistance? Ta Quote
Tarmac@TarmacSportz Posted July 17, 2011 Posted July 17, 2011 Hi Everbody I am new to this forum and wondered whether you could offer me some help? I have a 2003 350Z and whilst driving it today the throttle went and I am only getting 1500 revs, please can anybody offer me any assistance? Ta Think you need to take it to a garage tbh buddy Welcome btw Quote
Ricey Posted July 17, 2011 Posted July 17, 2011 So its revving to 1500 rpm or its ticking over that high? Did it go all at once or gradually. BTW - I won't be able to provide any advice with this information but one of the other mechanicy types might! Quote
Beau Posted July 17, 2011 Posted July 17, 2011 Is it going into Limb mode? Any Lights on Dash? Somemore info may help.... Quote
ryzf Posted July 17, 2011 Author Posted July 17, 2011 Hi It went all at once the EML is on TCS light is on and it only revs up 2 1500 rpm at full throttle ta Quote
ryzf Posted July 17, 2011 Author Posted July 17, 2011 yes it is an import and no its not in snow mode Quote
Beau Posted July 17, 2011 Posted July 17, 2011 Hi It went all at once the EML is on TCS light is on and it only revs up 2 1500 rpm at full throttle ta This happened to me once and then all fine! It happened to be a wheel sensor. Dirt got stuck in between it. Got some cleaning fluids in there and took it out in the wet for a drive. All fixed! Quote
Maccaman Posted July 17, 2011 Posted July 17, 2011 Hi & to the forum. Is it an import? Have you accidently knocked on the snow button? Quote
ryzf Posted July 17, 2011 Author Posted July 17, 2011 Hi I have checked and it not in snow mode, also tried to self diagnose fault codes with two different diagnostic code readers and they wont recognise the car/faults whats the best code reader to use on a import? Quote
Ricey Posted July 17, 2011 Posted July 17, 2011 Hi It went all at once the EML is on TCS light is on and it only revs up 2 1500 rpm at full throttle ta Garage to be on the safe side - I'd be tempted to say don't drive it there either.......unless its very close. Quote
DoogyRev Posted July 17, 2011 Posted July 17, 2011 Hi It went all at once the EML is on TCS light is on and it only revs up 2 1500 rpm at full throttle ta Garage to be on the safe side - I'd be tempted to say don't drive it there either.......unless its very close. +1 on that Quote
bronzee Posted July 18, 2011 Posted July 18, 2011 Welcome to the forum, and good luck with the fix. Quote
ryzf Posted July 18, 2011 Author Posted July 18, 2011 Hi well i now have the fault codes and I believe they mean the following: P1122 Electronic Throttle Control Actuator P1126 Throttle Control Motor Relay Any suggestions to what I need and is this going to be expensive? Thanks for you help Quote
M13KYF Posted July 19, 2011 Posted July 19, 2011 have you tried a ECU reset, a how to can be found in the guides. It may of just been a glitch Quote
marzman Posted July 19, 2011 Posted July 19, 2011 Were you giving it some at the time? The zed can go into limp home mode if you've been pushing it a bit hard... i would try an ECU reset as mike says... Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.