varley16

Is the gearknob for sale? pm'd you.

Pm'd.

Im in alsager, but not me.

Few months time ish and i may go for these.

When we planned our little one, permission was granted to keep the 350z, however when IT appeared, I tool the grown up approach, did some maths and some thinking and ended up selling as it was on finance, then fuel and the rest. However, the lad is 4 now and I was allowed another one, I got one and dont regret selling my first one, but all depends on pound coins. Also, I dont like the grown up version of me, so ignore all of the above.

Spent an hour ish at mopedmark having my bits blinged, apologies for a very dirty engine bay, but its a good start, a must do for all 350z's. A very genuine nice bloke, good to meet you and the family. Thanks for fitting me in today. Also, tarmacsportz have given me a mines splitter, zunsport grille and DRLs in exhange for money, probably fit them in the next couple of weeks.

Recieved, although i was slightly confused as i had no January......i worked it out doh!

Sold! dam it. Thanks anyway.

This could possibly be the most geeky post. Im playing Rfactor2, and race in a league called GPVWC, and have been signed to a team in the superleague. Sorry.

True, does this sit in the engine bay? Ideally i'm wanting it to sit behind front bumper.

I have seen this, however alot cheaper, also unsure of quality would put me off.

Thanks, much appreciated.

Ok, i will go from the maf housing, then sit the filter behind the bumper. So... 1 x maf adapter 1 x 100mm? silicone hose (ID 76mm) 1 x hose joiner- unsure of length? (OD 76mm) 1 x 90' silicone hose. (ID 76mm) 1 x hose joiner - again unsure of length. (OD 76mm) 1 x Cone filter 5 x hose clips.

Actually you may have a point, as the intake pipe has another pipe coming from it, where did you get the other intake kit from?

Looks good, I am more going for looks as I will be having my bits chromed.

Oh yes, I wont be cutting it just incase. Other than that does the shopping list seem like it would all pop together?

Hello all, This is my second 350z, and I purchased from a member on here a few months back. I had my first 350z in 2010, GT, GM grey. I sold this due to the wife and I think myself wanted one of them babies. We made one and although I was authorised to keep it, I just had to man up and face facts, so off it went. The time came to treat myself to another one, i didnt want a GM grey one again, so I purchased myself a 2003 GT 350z in GM grey 😯 It needed work, but some nice mods and low mileage I went for it. Mod list: 1. Red bride seats. 2. Scorpion exhasust. 3. Rota 18" Alloys. 4. Bonnet dampers. 5. Side diffusers. 6. Red wheel nuts. 7. 20mm front and 25mm rear wheel spacers. 8. Smoothed and resprayed centre console. 9. Android head unit. 10. Silly mirror stickers (sorry) 11. Mopedmark bling manifold, throttle body, and latch. Work completed. 1. Service and spark plugs. 2. OSF wheel bearing. 3. Aerial unit and stubby aerial. 4. Resprayed bonnet. 5. Replaced relay inside amp unit. 6. Replaced amp relay.

I have a shopping list together, if at all possible, can someone advise if i'm correct in what i'm ordering. My thoughts are, throttle body has 76mm internal diameter silicone coupling (100mm) then a 45' alloy pipe (outer diameter of 76mm) then another silicone coupling (ID 76mm) which is then attached to the maf housing, after this comes the 3rd silicone coupling (ID 76mm) followed by a 350mm alloy pipe (OD 76mm) which is then attached to a 90' silicone hose, this is the house that will go through the intake hole at the front by the headlight, this then is attached to a 200mm alloy pipe (OD 76mm) then finally the air filter. i've added 10 hose clips (70mm-90mm) 45° Degree Alloy Elbow - Polished Aluminium Bend Pipe Joiner Outer Diameter 76mm 76mm ID - Coupling Silicone Hose - Choose Your Length & Colour Length 100mm X 3 Colour Red 76mm - Custom Alloy Straight Hose Joiner - Choose Your Length - End Bead Optional Length 350mm Silicone Polyester Reinforced Hose - 76mm - 90 Degree Elbows Colour Red 76mm - Custom Alloy Straight Hose Joiner - End Bead Length 200mm Single Cone Performance Air Filter - Air Induction Filter Colour Red ASH - Hose Clips - Worm Drive Stainless Steel - Single Clip Clip Size 70mm - 90mm

How much for all 3, and do you do a drive in, swap bits for bits service?

Much appreciated guys

I have seen some people have custom cold air intakes, i have spoke to someone that has done it but he is unsure of the diameter of the pipes. He also recommended auto silicone hoses to shpply the parts, has anyone used these and know what parts I will need? Idealy I want the air filter to sit behind the front bumper/just under the bonnet latch.

What did you use for the piping around the edge? been thinking of doing this myself.

Red 370z at 1:55.

1. SuperStu (2 wall and 1 desk) 2. GMballistic (1 desk top) 3. Veeg33 (1 wall and 1 desk) 4. Andy_Muxlow (1 Wall and 1 Desktop) 5. rothers2901 (2 wall) 6. Kev T ( 1 wall ) 7. Mattross1313 (1 wall) 8. Vik54 (1 Desk) 9. eatonm90 (1 wall) 10. Varley16 (1 wall)

Welcome, you may see me on the a500 every day....stuck in traffic.....