ZMANALEX

Nicky, Tom at TGM at Fleet is your man. I have an arrangement with TGM for customers parts to be shipped direct to them which will save you lugging them around in your Zed. Alex

You can only access the outer bonnet pull cable form under the R/H front arch liner and not the catch

Is there anyway to test the mirror switch (I assume the round twisty knob you use to adjust the mirrors?) apart from the obvious of taking it out and fitting a new one? If new switch is only way I will take one soon of you, going to need some exhaust gaskets and bolts in the next week or two so might as well get them all at the same time. Is there a noise from the mirror when you are trying to adjust it? Nope no noise when trying left/right. Only sound I can hear I what I can only describe as a slight click coming from the door, maybe a rely or something? But the mirror motor is deffinatly not trying to move to the side. If you are getting a noise from the door area when working the switch then that probably points to a fault perhaps in the mirror. Without getting to technical on the proper test procedure, why not just swop the mirrors over. They obviously will not fit to the door, however the electrical connectors are the same. In fact all you have to do is remove the passenger mirror, disconnect the wiring block connector on the driver's side and connect up the passenger mirror to the driver's side and test. Alex

Is there anyway to test the mirror switch (I assume the round twisty knob you use to adjust the mirrors?) apart from the obvious of taking it out and fitting a new one? If new switch is only way I will take one soon of you, going to need some exhaust gaskets and bolts in the next week or two so might as well get them all at the same time. Is there a noise from the mirror when you are trying to adjust it?

to the forum Nicky

Nicky, You will have PM shortly Alex

Here you go mate, in stock and good to go same/next day viewtopic.php?f=157&t=29441 All this type of stuff can be found in my 9 page sub forum viewforum.php?f=157 Drop me a PM if I can help you further. Alex

Could be a mirror switch fault or a mirror motor fault so further investigation will be required, however all parts in stock if required Regarding the steering wheel being off centre. This should be corrected when the tracking is getting done. The steering wheel should be clamped in the straight ahead position before the tracking is adjusted. Take it back to the garage and get them to rectify this issue. Alex

Here you go mate: Service schedules are 9000 miles or 12 months, whichever comes soonest. P1 P2 P1 P3 P1 P2 P1 P3 P1 P2 That takes you up to 10 years or 90,000 miles Alex Why did you stop at 90,000 I have done that list + a P1 and need a P3 soon For the simpletons amongst us please just repeat

Here you go mate: Service schedules are 9000 miles or 12 months, whichever comes soonest. P1 P2 P1 P3 P1 P2 P1 P3 P1 P2 That takes you up to 10 years or 90,000 miles Alex

It will probably be the clutch pedal return spring which is giving you the single ping at the end of the travel It is located in the pedal box at the pedal fulcrum. Alex.

Next decent KRC track night is Tuesday 11th September 6pm - 8pm. This will also be a sell out so get booked early Alex.

Fully synth 5W30 Motul fully synth 5W30 in stock and good to go same/next day at £39.95 for 5 litres Oil filters and sump plug crush washers also good to go Drop me a PM if I can help you further Alex

They are advertised Where does it say that they are all sold? This has been a regular stock item for the past 8 years Alex

Why buy else where. Cheapest in the UK viewtopic.php?f=157&t=57136&p=822876#p822876 Alex.

All P1, P2 and P3 service items in stock and good to go same/next day. PM on its way Alex

Correct

Plenty in stock Ryan Alex.

Thank you CS Simon, PM received and replied to In stock and good to go same/next day Alex.

If it is the gasket that fits to the top of the inlet manifold which hooks up to the plenum then I have them in stock and good to go same/next day Alex.

As before spigot rings???? Tracking to get your wheels pointing in the same direction Alex

Geo will not effect wheel balance. Are the hub/spacer/wheel faces true? If spigot rings fitted are they the correct size? or perhaps you may not have spigot rings fitted when you should. Alex

Preowned senders in stock Steve, for both sides Alex

Very straight forward mate if you follow the guide Remember and swop out the large O rings as they can not be reused. I have them in stock and good to go same/next day if required Alex.

Jon, Calsonic is OEM and standard. The unit which is hooked up to the L/H rear sway bar drop link is indeed the headlamp self leveling as Doctor Austin has correctly stated Alex