Jump to content

SkylineV35

Members
  • Posts

    1,039
  • Joined

  • Last visited

Everything posted by SkylineV35

  1. So droplinks 90 degrees to the swaybar? Ok il give that a go thanks!
  2. My knocks were caused by droplink on front left and aftra while they eventully snapped i was only dropped 15mm but with eibach swaybars
  3. I have eibach anti rollbars and recently over the course of a year iv snapped 3 oem front drop links... my car is ownly lowered 25mm. So i have bought adjustable droplinks and set the sway bar so its horizontal and also hooked the link to the softest setting on rollbar.. however after a spirited drive iv noticed my frontend soaking up every pothole and dip on the road, to the point it shook the back and i could feel it losing traction. If i remember correctly with the oem ones the swaybar was sitting slightly higher around 20-25degrees. Iv read that to setup droplinks handtighten till it loads then tighten. But no matter how i set it up it was preloaded and couldnt hand adjust so just set them up the swaybar horizontal to the ground. After some reading on websites they say it should be 10-20degrees? Some say horizontal. What should i do?
  4. I got them on mine fine so far
  5. How do I order from here? Will it fit my V35 Skyline?
  6. Gear surround or where sub is..
  7. How much are they roughly? Its ok found them
  8. Im sure i read somewhere theres a weight in the bootlid somewhere too..
  9. You mean connect the two wires at sensor unit? Il give that a try when it stops raining. Yeh its a silly glowshift thing from the states only chose the set because it had purple to go with my colour scheme at the time.
  10. My v35 doesnt have oem oil gauge. So just get a mechanical pressure gauge from harlfords or something and plug it to the block? Where would be best location to plug it to?
  11. I had some gauges in for a while now and all have been working fine until recently my oil pressure gauge just sits at zero no matter if im idle or driving at any given speed. Before on cold start gauge would switch on do a sweep and sit at 80-90psi then after car warms up it would sit 20-30psi. Now it goes to max psi and slowly drops down to zero and stays there. I have checked all wiring replaced sender unit and still same.. is it possible gauge isnt working? Or do i actually have no pressure? But surely if I had no oil pressure the dash lights would flash? Iv also done an oil change while i was under. Is there any other way I can test? The car seems fine no knocking noises and sounds fine... oil levels are fine.
  12. Just remembered I have a build thread.. well things werent going well last year, I wanted to open up the headlights to spray the inside black or colourmatch the body colour. Stuck it in the oven got distracted came back to melted headlights and the list goes on... will update with pictures soon the phone i had at the time brand new htc m9+ touch screen died so trying to get the pictures out of the old one.
  13. Feels like every new hot hatch makes 300bhp+ my mates drive Golf R, new Civic TypeR and Audi S3 quattro 8v, I dont even bother trying to keep up anymore
  14. Anything you guys would suggest doing to reap maximum benefits? Iv done plenum spacer, mrev2 plenum, 100cell sports cats, full exhaust system, earthing kit, ams pulleys, changed oil/oil filter and spark plugs recently,ztube and hks panel filter.
  15. seen on on ebay but it was the one with oil cap the wrong side.. 28pounds though... could i possibly use this? anyway im looking for rocker cover for vq35de engine thanks
  16. Oh yeah il give that a try later if the rain holds off =)
  17. Haha yeah I read your post earlier thanks. But its the extra code P0057 am worried about most I think its the sensor post cat
  18. Been a while since iv posted but just wanted to double check something I have the above codes thrown up. I have decats fitted with 02 extended spacers, usually only the p0138 code throws up and I just erase codes with my reader but yesterday it pulled up the above 3codes. Heater circuit low code is this still due to decats or do I have to replace the bank2 sensor? I read there is a fuse box with a 15amp fuse for 02sensor will check that later. But main query is are these the usual codes that throw up and can be taken away permanently with uprev? Also if the sensors are faulty im assuiming if i get remap it means I wont need to replace sensors as they arent being used anyway? Thanks in advance
×
×
  • Create New...