Jump to content

RobPhoboS

Members
  • Posts

    2,859
  • Joined

  • Last visited

1 Follower

About RobPhoboS

  • Birthday 08/08/1980

Location

  • Location
    Hampshire

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

RobPhoboS's Achievements

Z Veteran

Z Veteran (5/7)

668

Reputation

  1. For sure I still want them serviced just as they're nearly 20 years old 🥴 And I just want to make sure they're in good condition before another remap. I had presumed that it was going to be around £165-ish anyway, and he seems like a good one to use.
  2. Funnily enough I had contacted him as well last week about having my set serviced but the price is more 😆 £22.50 per injector (includes full testing, spray analysis, cleaning internally, flushing the debris from within, final flow testing and balance matching the set) The kit of parts is installed at a separate cost, likely £15.48 for a 6 cylinder kit containing new upper and lower Viton seals. The return postage would be £15.00 within the UK. I still want to have it done, just as they've not been serviced before.
  3. No offence to you but for the love of ICE - DO some research, and don't rely on forums ! You get one shot at doing this right. 😂 You'll have to decide what's best because you'll get conflicting info from well intentioned people. I rebuilt my engine at home 3-4 years ago, and had to break\run it in on the road, whereas 350Butcher had it on an engine dyno (not chassis). This is what I followed, listened to and did - is it correct/perfect - too late now 😆 https://dsportmag.com/the-tech/education/quick-tech-performance-engine-break-in-the-right-way/ https://www.youtube.com/watch?v=-yRudUHeSng (3 parts) I really like Lakespeed Jr, so have a search for him on YT (works with Total Seal piston rings now), huge amount of knowledge and very humble speaking to others: https://www.youtube.com/watch?v=kJw1_levGew I used: Millers Oils CRO 10w-40 Competition Running In Mineral Engine Oil (call Opie Oils and see if they can help needs be). Oil viscosity (running in, and after) depends on your build and clearances on the bearings (don't assume stock is correct). After running in, drop the oil and carefully open up the oil filter and inspect it. You'll likely see swarf, so ensure that you have enough of your normal oil and filters to run it and drop it again to help flush it out, repeat as required, it will bugger off eventually. It's totally down to you how long you run it and drop it again (I verged on the paranoia side of things). It's one thing I didn't see many industry people talking about much. I use this for cutting the filter: https://www.amazon.co.uk/gp/product/B09J2M1WVX/?th=1 Good luck 🙌
  4. No it won't. Have a read of this or check youtube for what they do: https://fluidampr.com/engine-vibration/ It is better for the engine, and worth doing depending on age/mileage.
  5. It's been ruddy ages, hope all is well for you and the team too ! ❤️ I will certainly be in touch after we've moved 😅
  6. Just to chip in, if anyone is on the fence about them - I've got an old Vipec ECU that runs on the Link G4+ platform, it's seriously good and the UI of their software is friendly. Their forum is really useful, and plenty of active users willing to help It's well worth learning a bit about them, and in this instance I'd recommend Evans Performance Academy over HPA (or both to plug any gaps).
  7. Well that sucks ! But you're kind of lucky too in some respects. You're only going to know the state of the heads & parts once it's taken off, and checked over for leaking/bent valves (plus checking pistons for any contact). Ideally you want to know exactly what caused the failure, rather than just blindly replacing bits and pieces. At 190k miles, yes definitely replace all of the timing stuff, water pump, and at least strip and clean/inspect the oil pump too if you're going to keep this car. No harm in replacing the cam with a good used one. If you're going to do it yourself, you'll definitely need a decent selection of tools, some cover and you're going to need to have the heads resurfaced and valves checked/cleaned by a professional. So yeah, either fix it yourself (and get the right tools), get someone else to do it, or sell it as is and take the hit. 🤕
  8. Hey Alex - just checking if you have a RevUp lower half plenum ?
  9. Depending on your exhaust tips, I've got a couple of Decibel Devils for sale (just need to amend my 'for sale' thread) - of the 2.5" variety. I recently just bought a 5" DD for my new exhaust too. They do help, even if it's a few db's, can get you by the day and take 2 mins to fit. I've not done this circuit yet but it's one I'd like to try this year once my car is sorted.
  10. Great to meet you timww1966 I hope she enjoys the exhaust as much as I have ! The DD's are still for sale but I'll start another thread for those I think.
  11. My car is a 2004. I'm not sure what the stock HR y-pipe is like, as that's what this would connect to. Assuming that the end of the Y-pipe is a 2 bolt flange, 3" and centrally located, I imagine it should fit. However, I'd recommend you do some research first to double check
  12. The future looks more and more planky to me 😭
  13. If someone has their old, spare 2004 air box kicking around, please pm me. I'm going to hack it up if it suits my needs, so not worried about the condition really. EDIT: Found one for a reasonable price on ebay (no not one of the cheeky morons trying to sell one for £150 + ffs ).
×
×
  • Create New...