Fluke

Those are the Those are the spin caps I was referring to.

The spin caps, just turn so no grub screw they are hard to remove unless you have the key. they cost about £6.00 a set on ebay.

Get your self some spin caps. They don't come with the logo, but despite finding tiny finger prints in the brake dust, I have never lost one yet.

Here's how everything is looking so far. looks like I will need to trim around the number plate area.

Next to the batter and fuse box you will see the cars wiring harness. Carefully cut a slit in the rubber grommet that contains the vehicle wiring harness. The amp power cable can then be fed down into the passenger foot well. Make sure you re -seal the cut with silicon sealant to stop water seeping into the car.

To be honest mine doesn't look too bad. I can't get RT to fit it as they are too far away. My car is my daily driver and I thought it might be easier to try and fit it my self and then remove it and get it dropped off for painting.

If he's local I have both a DA and Rotory he could borrow for a day to 2.. At no cost.

There are no pre-drilled holes anywhere.

Thanks. the Chargespeed I have is from RT. I have a spare bumper and plan to use that as a template for all the holes etc.. And hopefully it will fit without needing trimming as. I just want to send it off to be painted.

Can anyone with a Chargespeed rear bumper fitted to their 350z please do me a favour and post up a picture of how the number plate light and boot release look? I am planning to have a go at fitting mine before send it off to be painted.

Thanks.

Has anyone managed to fit a Motordyne Shockwave TDX2 with a Chargespeed bumper? How much modification is needed? Is it just a case of enlarging the exhaust cut outs?

Can anyone tell me or recommend what size spacers I would need to fit 370z Rays to a 350z?

I am just about to fit HEL brake braided lines, can anyone tell me if a fitting guide is available? Does the line also replace the hard brake pipe?

Oops, can a mod please move this to the correct forum?

I'm still looking for an exhaust to replace my Milltek on my 350z and can't decide between a Stillen, Invidia or an Ark everything seems to be out of stock just lately, but whilst looking I came across this site that has some great sounding exhaust clips I though might be of interest. http://370zexhaust.com/

I just don't have the patience, what at about the Motordyne?

I also like the look of the 350z Motordyne Shockwave TDX2 Exhaust.

I want to change by Miltek Berk HFC combo for something louder but without the drone on motorway journeys . I'm still undecided as to which exhaust to get, I like the Ark Grip, but it's going to be the end of Sept before anyone has them in stock. I know the Stillen is dearer, but has anyone heard it and could share their thoughts on it? I I have been working 7 days a week for the past few months, but have the weekend off next week and want to treat myself/install a new exhaust. I have also have a Chargespeed bumper to go on, sp whatever exhaust I go for needs to fit without having to chop that up.

I went Ark with standard cats, I love it, had the Miltek with HFC's before that, no contest. what at is it like when just cruising at motorway speeds?

Hi mate, I have the chargespeed rear and the Berks HFC's along with the Invidia Gemini, love the sound of it,not massively overloud and a nice burble on tick over, that with the rear end, think you'll be happy with the choice is there any chance you could post up a video?

I love the look of the Ark, but as I have a chargespeed to fit they won't be seen and I don't want to mod the bumper, so I'm leaning towards the Invidia at the moment. I plan on putting an order in sometime this week when I've made up my mind.

Where abouts are you?

?

Can anyone that has heard both exhausts tell me which is the loudest or sound the best?