Vlad Posted February 4, 2013 Posted February 4, 2013 Getting few bits soon from Alex to service my Z. Dealership, i bought Z from, serviced it before i picked it up...but since I had few problems with them - so wondered if they serviced it properly and decided to service it myself and change everythng i can. Searched and found guides on how to change gearbox/diff oils, brakes/brake fluid and so on... but cant find one for clutch fluid? unless im going blind lol Have anyone done it and fancy sharing some information? would be much greatful Vlad Quote
ZMANALEX Posted February 4, 2013 Posted February 4, 2013 Vlad, I have a hard copy of the procedure for changing the clutch fluid and proper bleed procedures. I will scan over and post up when I have a minute, however I will include a copy with your fluids and service stuff. Regards, Alex. Quote
M13KYF Posted February 4, 2013 Posted February 4, 2013 it would be great if you could post the scan on here Alex Quote
Vlad Posted February 4, 2013 Author Posted February 4, 2013 oh wicked stuff! Thanks a lot :yahoo: Quote
ZMANALEX Posted February 4, 2013 Posted February 4, 2013 (edited) CL-8 CLUTCH FLUID CLUTCH FLUID PFP:00017 Bleeding ACS0014Z CAUTION: Monitor fluid level in the reservoir tank to make sure it does not empty. Do not spill clutch fluid onto painted surfaces. If it spills, wipe up immediately and wash the affected area with water. Bleed the operating cylinder. 1. Fill the master cylinder reservoir tank with new clutch fluid. 2. Connect a transparent vinyl hose to the air bleeder. 3. Depress the clutch pedal quickly and fully a few times and hold it. 4. With clutch pedal depressed, open air bleeder. 5. Close air bleeder. 6. Release clutch pedal and wait for 5 seconds. 7. Repeat steps 3 to 6 until no bubbles can be observed in the brake fluid. Air bleeder: : 5.9 - 9.8 N·m (0.61 - 0.99 kg-m, 53 - 86 in-lb) SCIA1496E Edited February 4, 2013 by ZMANALEX Quote
Vlad Posted February 4, 2013 Author Posted February 4, 2013 Thanks might be a stupid question, but... before step 1....how do you get rid off old fluid? Quote
ZMANALEX Posted February 4, 2013 Posted February 4, 2013 Suck 90% of it out from the reservoir with a small syringe and then refill with fresh. Alex Quote
Vlad Posted February 4, 2013 Author Posted February 4, 2013 oh wicked step 2.... do you know diameter of the hose needed?lol Quote
Vlad Posted February 4, 2013 Author Posted February 4, 2013 typical... after I got answers, google decided to be nice to me and give me that: ^^ clutch oil change instructions... for infinity g35.... which i guess going to be same process for 350 Quote
Grundy Posted May 6, 2015 Posted May 6, 2015 (edited) How much fluid is needed for a clutch fluid change? Edited May 7, 2015 by grundy225 Quote
Kaveney Posted May 7, 2015 Posted May 7, 2015 (edited) I got through 500ml ish doing my one but that was with a fair bit of flushing and pipe change . Just don't let the fluid run too low or you will lose all pressure and need to prime the slave . Alan Edited May 7, 2015 by Kaveney 1 Quote
DarmoZ Posted August 11, 2015 Posted August 11, 2015 Is it best to install new braided lines and slave cylinder prior to fluid bleed / change, or after? Quote
Ewen@Clark Motorsport Posted August 11, 2015 Posted August 11, 2015 Its worth trying a fluid change first but if it does turn out to be the cylinder you will have to bleed the system again Quote
gstraw Posted March 17, 2016 Posted March 17, 2016 thread revival! is clutch fluid just brakefluid? if so should it also be upgraded to 5.1? Quote
ZMANALEX Posted March 17, 2016 Posted March 17, 2016 Brake and Clutch are similar fluids. RBF 600 or 660 works well. Quote
RobPhoboS Posted March 17, 2016 Posted March 17, 2016 This is the other vid of the same thing if any use. Quote
gstraw Posted March 17, 2016 Posted March 17, 2016 Anyone else think that guys video was incredibly long. Easily can be done in a 3 minute video lol Has anyone done it his way? Seems easier than getting under the car Sent from my iPhone using Tapatalk Quote
RobPhoboS Posted March 17, 2016 Posted March 17, 2016 Anyone else think that guys video was incredibly long. Easily can be done in a 3 minute video lol Has anyone done it his way? Seems easier than getting under the car Sent from my iPhone using Tapatalk Better that you see it all or someone will moan about that ! Quote
bezza1121 Posted April 7, 2016 Posted April 7, 2016 Bleeding mine tomorrow with RBF 600, thinking the fluid is due a change. Hoping this will solve my recent inconsistent clutch feel and slight squeak noise when pressing down clutch. 1 Quote
jonny the mod Posted June 5, 2016 Posted June 5, 2016 Afternoon people. Just been reading this issue as its just happened to me. Guess the best thing to do is replace cylinder and fluid just to be sure... I will probably get ATS to do it as its just around the corner, but can anyone tell me how much a new cylinder will cost so I dont get shafted. Cheers Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.