Adam rs

Deposit taken, Thanks everyone. Back in the evo then

I HAVE ALSO DONE OIL AND GENUINE NISSAN FILTER WITH MOBIL 1 5W/30 YETSERDAY I WILL TRY AGAIN WITH PHOTOS TODAY. I CAN ALSO BE CONTACTED ON - I AM CURRENTLY USING IT SO CAN BE VIEWED ANY TIME

I AM RELUCTANTLY SELLING MY DECEMBER 2004 350Z GUN METAL GREY FACTORY FITTED FULL N1 BODY KIT BLACK LEATHER UK GT ON A 54 PLATE MY CAR SINCE 2011 AND 18500 MILES CURRENTLY ON 26000 EXCESSIVE NISSAN HISTORY TO MY OWNERSHIP THEN MAINTAINED BY ME WITH RECIEPTS TRACKER BLUETOOTH HANDS FREE BIRDVIEW SAT NAV BOSE AUDIO 06 AIR BOX MOD HKS PANEL FILTER TEIN SPRINGS PLENUM SPACER MILTEK SYSTEM WITH Y PIPE BERK MOT COMPLIANT HIGH FLOW CATS AMS PULLEYS UPREV MAP BY RS TUNING 300 BHP 12 MONTHS MOT 6 MONTHS TAX THE CAR IS IN THE CONDITION YOU WOULD EXPECT FOR 26000 MILES FRONT BUMPER SPRAYED 500 MILES AGO £6995 WITH STANDARD 18" WHEELS £7450 WITH 19" LINEA CORSE WHEELS CAR IS LOCATED NEAR HULL/YORK CANT UPLOAD PHOTOS BUT I THINK THERE ARE SOME ON HERE PM IF INTERESTED ADAM

Brake shield behind disc?

I use my meguiars metyl polish on all my lights. Its a very fine abrasive and works well.

Get it blasted and coated. Probably £50 and you would have to take it off to fit another anyway.

my miltek is well clear of the tarmac. My bumper takes more hits than the exhaust.

Sell the car and buy a faster one. Ive spent a fortune on 14bhp My evo gains more than that on a cold day!

Ebay

welcome to the club. The miltek is nice and quiet even with berks.

That's good work to get extra 25hp on a N/A engine. Better MPG too?

Get this done if you have berks fitted,had to abort my first dyno run before uprev due to dangerously lean fuelling.

My plenum spacer is from Horsham,Fast delivery and good advice. Get t mapped though if you have de cats as fuelling will be dangerously lean!

How did this go?

I dropped profile on mine and didn't notice. 20s will look great anyway so do it.

HSD on my evo from driftworks, Not seen one complaint on any forum. Get the mono tube kit. Fantastic value setup.

I had plenum spacer/ milltek/induction/upprev map made 294 and275lbft Added lightweight puleys and berk hf cats then a 2nd uprev map.Only 2bhp and 2lb ft more!

The youtube video is usefull.Make sure you have plenty of extensions ready and a torch.Much easier than I thought it would be.

Make sure you budget for a re map as my afr's were dangerously lean when run up on the rollers after fitting.

Love my miltek and the fit and quality are excellent,Nice and quiet too.Best money I have spent on the car but will get tinny at about 4k rpm if you add hfc,s.

Very good,Nice bit of old school porting. Bit more thinking,Bit less spending. Excellent figures. Good work.

I have exactly the same codes as you,Had my uprev done 12 months ago never had a problem till sunday. I have HFC's but they were fitted before the uprev. Funny the cold weather is mentioned as ive never used the car when its been this cold. I will keep re-setting the light and will be interested to see if it is the weather. I will add to the post if anything changes.

Money sent,Thanks.

Had OBD scanner on her- Heated O2 sensor 1 Heated 02 sensor 2 Maybe sports cats threw it on. If id have had de-cats the light warning for this would have been disabled on the uprev. Light not been back on,all seems OK!

Done ecu reset. Been round the block for 10 minutes. Light still off,I would have thought it would have come back on if there was a fault. Fingers crossed.