cs2000

No worries guys, glad you've all got on well. Still waiting for @alfa_owner but I think he doesn't know these are ready since nobody is getting email notifications on the forum at the moment! Other than his two, I have 2 currently in stock ready to go

Same here, been like this for around A week or so now at least. Also using gmail. il flag my own post, see if we can get an admin to take a look

Finally, these are done!! Looks like the boat from China took a long detour.... I have 5 modules ready to go which means everyone on the current list is accounted for. PM's have now been sent to everyone on the list but its likely nobody will see it since nobody is getting email notifications. As a little something extra (but pointless really!) Il be putting a PCB into the package too. Its a non functional early prototype of the design. I have about 40 of them in various development stages and god knows what to do with them so thought it might be cool to put one in each package 1. DOOM! (350z) - PM Sent 2. daisyduke (350z) - Posted 3. longsho7 (350z) - Posted 4. Rickdon (370z) - PM Sent - Waiting for 370 Guide 5. Keyser (370z) - Posted Also have another 4 modules almost ready, just waiting for the buttons to come into stock, other than that, they're ready

Ahh OK, well the other option is to go full AN spec. Each pipe would need https://www.viperperformance.co.uk/fuel-hose-fittings-and-separators_10061_straightptfe-swivel-end-fittings.html 2x - PTFE-S-6 BK https://www.viperperformance.co.uk/fuel-hose-fittings-and-separators_9957_an-to-nptmale-adaptors.html 2x - ADAP-6-1/8NPT and the length of tubing you need in PTFE stainless braid https://www.viperperformance.co.uk/braided-fuel-hoses_9864_ptfe-hoses-t-e-f-l-o-n-braided-stailess-steel-fuel-hose-fuel-brakes.html PTFE-06 HOSE That hose is rated for 12,000 PSI working pressure. But, it may not be worth the time/investment

Haha that was a brilliant end to the video. Its the kinda thing that braided lines are meant to stop (if i understood the failure mode right). Could you get some braiding and braid the line yourself? Otherwise, looks brilliant, nice and slow and controllable! Im guessing this hose wouldn't be correct? 300 mm 1/8 inch BSP and meant for carrying gas. I dont know if you wanted male or female though. It seems like googling "airbrush hose" gets you the right things, i think https://www.manomano.co.uk/compressor-accessories/sealey-ggh300-rubber-delivery-hose-flexible-300mm-1-8bsp-gas-1401120

Perfect, thanks! I didnt want you sat there thinking i had ripped you off or something, thats all! haha.

Hey all, don’t worry I haven’t gone anywhere! all the components I need to build all of the boards have arrived. I’m therefore hoping to build and test all of these over the weekend. as before, the missing component is some large heatshrink (still) and I really need this before I can send these out. Il update you again when I have some more news

Awesome, can’t wait for this to all come together. Really hope I can follow in your footsteps and do this too!

Any HR/DE owners out there who haven't installed this yet, I have uploaded new instructions to the web server. If you've already downloaded the instructions, I suggest downloading them again as the wiring should now be 100% thanks to advice from Bailydom, Jack94 and taybo 1. alfa_owner (2x) - Deposit Received 2. craigmdennis - Posted 3. StuZGT - Posted 4. baileydom - Posted 5. Kryptek49 - Posted 6. Jack94 - Posted 7. PabloVC - Posted 8. Jcurtis - Paid 9. Skate2create - Posted 10. Nelly64 (2x) - Posted 11. Luke2208 - Posted 12. btoms350z - Posted @Jcurtis - I have your money but i dont have your address, module is all ready to go as soon as i knpow where im sending it. @alfa_owner - Guessing you're away on holiday or something, still waiting for payment from you mate As mentioned, got these in stock now, so have them ready to go next day !

Thanks for the update guys, il reference my PM and update the instructions, at least we/i have confirmation! Current list is as follows 1. alfa_owner (2x) - Deposit Received 2. craigmdennis - Posted 3. StuZGT - Posted 4. baileydom - Posted 5. Kryptek49 - Posted 6. Jack94 - Posted 7. PabloVC - Paid 8. Jcurtis - Deposit Received 9. Skate2create - Posted 10. Nelly64 (2x) - Paid 11. Luke2208 - Posted 12. btoms350z - Posted Still got 2 of these in stock and ready to go at the moment, will have to order some more shortly if people still want these moving forwards.

OK guys, thanks for your payments over the weekend! Anyone who has paid right now, il get these out to you tomorrow at some stage. Im in Manchester foir the next 2 days for work and so anyone that paid tomorrow will have to wait until Wednesday for postage. Of course, if anyone else on the list pays tonight ( @alfa_owner, @PabloVC and @Jcurtis ) il take the parcels with me and post tomorrow.! EDIT: all paid items have been posted just now. Will try to sort you all out with tracking numbers tonight, but I am away with work at the moment.

Buttons have now arrived for most of the boards, still waiting on the heat shrink! i have tested both of the modules currently built and all work perfectly, also edited the instruction guide with new, better photos of the actual production PCB and wire colours. so annoying to be held up because of some bloody heat shrink! But it’s needed! Really hope it turns up this week! i did need a few more components to build the rest of the boards (missing some resistors) but they should be with me by Wednesday when I’m back home from my quick business trip (mon and tues) As usual, il keep you updated!

Right! the day has come! FInally got everything in I need to finish these so ready to get them made and sent out today/Monday. Everyone on the list now has a PM in their inbox saying what to do next . Il keep this list updated as people pay and modules are shipped. Youll all get a PM with your tracking number once I have it too 1. alfa_owner (2x) - Deposit Received 2. craigmdennis - Posted 3. StuZGT - Posted 4. baileydom - Posted 5. Kryptek49 - Posted 6. Jack94 - Posted 7. PabloVC - Posted 8. Jcurtis - Deposit Received 9. Skate2create - Posted 10. Nelly64 11. Luke2208 - Posted 12. btoms350z - Posted I also now have 3 of these in stock currently, so anyone else interested, these should be available immediately from now onwards.

From my PM's with Martin, he likely wont be around the forum again until December time, so you guys may have to wait a while.

I did actually "borrow" @taybo's wire colour guide as he has posted above. What im after however is just 100% confirmation that the drawing is correct and what the pin numbers are so I can add them to the guide. The wire colours ARE correct however, just maybe not their positions on the plug. I have PM'd taybo to double check for me too

Looks good mate. if you need any assistance on the PCB layout or arduino coding, give me a shout I know that PCB is a one off prototype, but im sure i could get that smaller if i built it in Eagle and had it printed over at JLCPCB, but for a rev 1.0 design, it does what it needs to do by the looks of it!

Deposit from btoms350z received so new list is below 1. alfa_owner (2x) - Deposit Received 2. craigmdennis - Posted 3. StuZGT - Deposit Received 4. baileydom - Deposit Received 5. Kryptek49 - Deposit Received 6. Jack94 - Deposit Received 7. PabloVC - Deposit Received 8. Jcurtis - Deposit Received 9. Skate2create - Deposit Received 10. Nelly64 11. Luke2208 - Deposit Received 12. btoms350z - Deposit Received @craigmdennis Glad you got it fitted OK and my guide was helpful! Whoever does the install first on both a Rev-Up and a HR, just double check your connections are 100% right. If theirs any doubt, give me a PM first. Id be grateful if anyone who does this install first on these cars can send me a picture or a list of the exact wire colours and pin numbers so i can make sure the guide is 100% correct. I want to make it as easy as possible and im pretty sure for the Rev-Up its correct, but dont have any photographic evidence to confirm it. I suspect the HR is the same as the Rev-Up, but again, cannot confirm.

@btoms350z - Apologies for the delay, have been in Belgium all weekend with the Z watching the F1. Il send you a PM now mate. Everyone else, still waiting on stock of some parts, if timings work out like usual, they should be here late this or very early next week!

Hey guys, I'm just back from a amazing, but extremely wet weekend in Spa for the F1 and have come home to some nice PCB's from China! I have so far built up 2 boards, but I'm waiting for the buttons to come through the post, and some heat shrink. As soon as these two little bits arrive, at least the first 2 boards will be ready to go! I have updated the first page with a photo of the actual filled board design, now in a lovely white solder mask!

It’s possible, but not going to be looking at this for a while yet. from my research, the American guy KP Technologies, did offer something to disable the feature so you could retain brake lights but do burnouts, but he was getting horribly inconsistent results when he sent 5 modules to customers, I don’t want the same issue so not sure if it’s something I would Persue, we will see. For example is 100% doesn’t work if you have an auto. the issue is that you can’t just turn “off” the brake signal by cutting a wire or wiring in a switch. If the car is moving and the ECU doesn’t see a “brake” signal for a while, it will throw a MIL on the dashboard. You have to put something inbetween which sees your brake input, sends the signal to the ECU as normal for a split second, then removes the signal again so you can do a burnout, not simple to do, but like I said, possible.

Looks amazing! Hope you get the air leaks sorted, then we need some propper external photos and videos too. Is the pump loud?? I always imagine them sounding like a garage air compressor!

Looks great Chris, cant help feeling partially responsible for this though!

Hi Luke, always available mate, will PM you now. 1. alfa_owner (2x) - Deposit Received 2. craigmdennis - Posted 3. StuZGT - Deposit Received 4. baileydom - Deposit Received 5. Kryptek49 - Deposit Received 6. Jack94 - Deposit Received 7. PabloVC - Deposit Received 8. Jcurtis - Deposit Received 9. Skate2create - Deposit Received 10. Nelly64 11. Luke2208 - Deposit Received 12. Since i had one module ready to go (the one i briefly used for testing), i have today sent this to "craigmdennis", so thats the first one out the door. Sorry alfa_owner, i know you were first on the list, but i didn't have 2 modules ready so had to skip to number 2 on the list. As soon as everything comes into stock for the batch ive ordered il be in touch again to get these sent to you guys, from then on wards il maintain a stock of these at all times so i can fulfil orders quickly.

Those Mechanical relays boards are normally pretty good, but general overkill for what i have needed in the past, They're usually fully opto isolated etc which sometimes is needed, other times not and can complicate matters. On my VDC/Traction control boards im just protecting from back EMF with a simple diode across the relay coils, seems to work well. Looking at your boards, your original solid state relays weren't opto isolated., the new ones (blue relays are) but i cant see any EMF diode on the board in the photo you've put up. Looking forward to seeing progress!

I had to replace this on mine too when i first bought the car, very easy fix, just loosen 2 bolts (or maybe screws, cant remember), i suspect @ZMANALEX is your man for the parts (i believe mine came from him originally.