EML

[Rock_Steady]

Yes, that dreaded EML, and after a re-map too!! Car still runs fine though.

 

So, i'm going to try and reset the ECU, should i try disconnecting the battery first?

 

So annoying.

 

Has this happened to anyone else after a re-map?

[ZMANALEX]

Best to pull the codes before you clear, just to see what is going on.

 

Who did the remap for you ?

[GeorgeW]

mine has come on a few weeks ago, took it to check the code and its the o2 sensor, havent sorted it yet but the car is acting normal. Tried clearing it a few times and it comes back. My guess is it was after the plenum spacer was put in?

 

could be something simple like that?

[Rock_Steady]

Best to pull the codes before you clear, just to see what is going on.

 

Who did the remap for you ?

I had the re-map done @ Abbey who cancelled the O2 sensors

 

mine has come on a few weeks ago, took it to check the code and its the o2 sensor, havent sorted it yet but the car is acting normal. Tried clearing it a few times and it comes back. My guess is it was after the plenum spacer was put in?

 

could be something simple like that?

could be, but after a re-map? seems a little odd.

[ZMANALEX]

Best to pull the codes to establish what the issue is.

[Rock_Steady]

Going to do that this afternoon with a friend's snap on tool.

 

i'll report back

Edited June 6, 2016 by Rock_Steady

[Rock_Steady]

ok so here are the codes. 3 of the buggers:

 

P0605

P1564

P1283

 

Apparently P0605 means that the PCM/ECM has a fault. i read that sometimes this code is thrown up after a re-map.

 

P1564 means there is a fault with the cruise control or cruise control switch. the funny thing is, my car has no cruise control

 

P1283 is something to do with the lambda sensors.

 

i have had all errors deleted along with the EML, so i'l take it out for a spin for a while and see if it rears its ugly head again.

Edited June 6, 2016 by Rock_Steady

[Richf]

P1564 = ASCD STEERING SWITCH

P1283 = A/F SENSOR 1 (B2)

 

P0605 is a generic code + P0605 Internal Control Module Read Only Memory (ROM) Error

[Rock_Steady]

Nope! EML came back on after a 20 minute run.

 

Is there anyone that can show me the way forward? What should i do next?

 

Lambda sensors?

 

[Richf]

http://www.autocodes.com/p1564_nissan.html

 

I'd be looking at the steering switch first

[ZMANALEX]

I would recommend that you clear all the codes and then once the EML comes back on , pull the codes again to establish what the current issue is as some of your codes may have been archived

[Rock_Steady]

i'll get the codes checked out again tomorrow and see what's what.

 

http://www.autocodes...564_nissan.html

 

I'd be looking at the steering switch first

if this is in reference to the cruise control switch, mine doesn't have cruise control. Mine is the boggiest of the bog standard zeds.

[Rock_Steady]

Update: Spoke to Mark at Abbey. He has had a look at the codes and thinks it's a little odd but he has offered to come to my house and sort it out for me free of charge.which is fair enough. Top man!

 

He has said that maybe the tolerances are not quite right.

Edited June 7, 2016 by Rock_Steady

[davey_83]

ahhh thats MEGA!!

[Rock_Steady]

ahhh thats MEGA!!

Yeah i know!!

 

He said it's nothing serious and the car is still fine to drive if i want to prior to his arrival.

Edited June 8, 2016 by Rock_Steady

[Rock_Steady]

Update: Mark's been round and sorted out the problem on the drive way. It appears that he used a map for a GT car which mine is not. Even though it shouldn't matter it did. It doesn't have cruise control and that was what was causing the ROM error. A quick flash of the ECU with the right data and it was done. Superb!!