How wide

[teamshock nick]

Hi

 

How wide (ET depending) will the 350z take without any arch work?

[BillyZed]

it all depends on how low you are?

[ATTAK Z]

why would you want to know ?

[BillyZed]

The wider the better

[Jay-350z]

12j et5 is about as wide as you can go, but will need arch work and stretch. And about 10j fronts.

 

Edit: just read the question, maybe 10j et 20.

Edited December 27, 2013 by Jay-350z

[BillyZed]

I was running 9.5J ET2 on the front and around ET - 3 on the rear. I was quite low though and had to get my rear arches rolled

 

Ideally if I was doing it again I would go much more aggressive! add another 20mm each side

Edited December 27, 2013 by BillyZed

[StevoD]

perfect set up with out any problem unless you go belly scrapping is 9.5 et 20 front and 10.5 et 20 rear

[JetSet]

Without lowering, 11J with ET 10 and 285/30/20's will fit on the rear. For 12J you'll need some arch work.

 

 

 

 

 

Pete

[teamshock nick]

Hmm

 

I have a set of 18x10j et -16 and 18x12j et - 20 pcd 5 x 114

 

I'm thinking about buying a 350z and wondered if they would go on. I can do arch work to be honest and the car is likely to be on air.

 

Is that pcd correct for a 350?

[Jared350z]

I run 9.5j ET20 all round with a 5mm spacers on the front and 25mm at the rear. Mines lowered slightly but there is still room to go wider without rolling my arches.

 

hope that helps a little.

[teamshock nick]

Yes thanks

[BillyZed]

yes 5x114 is the correct PCD

[Jetpilot]

I run 9.5j ET20 all round with a 5mm spacers on the front and 25mm at the rear. Mines lowered slightly but there is still room to go wider without rolling my arches.

 

hope that helps a little.

 

No rolling on the rears with -5, is that with a fair bit of camber and stretch on the tyre?

Edited December 28, 2013 by Jetpilot

[Jared350z]

I run 9.5j ET20 all round with a 5mm spacers on the front and 25mm at the rear. Mines lowered slightly but there is still room to go wider without rolling my arches.

 

hope that helps a little.

 

No rolling on the rears with -5, is that with a fair bit of camber and stretch on the tyre?

 

I dont have -5 on the rears or have you quoted the wrong one? As for tyres I run 225/45/18 (front, stretched) 245/45/18 (rear, little stretched)

Edited December 28, 2013 by Jared350z

[Jetpilot]

I run 9.5j ET20 all round with a 5mm spacers on the front and 25mm at the rear. Mines lowered slightly but there is still room to go wider without rolling my arches.

 

hope that helps a little.

 

No rolling on the rears with -5, is that with a fair bit of camber and stretch on the tyre?

 

I dont have -5 on the rears or have you quoted the wrong one? As for tyres I run 225/45/18 (front, stretched) 245/45/18 (rear, little stretched)

I run 9.5j ET20 all round with a 5mm spacers on the front and 25mm at the rear. Mines lowered slightly but there is still room to go wider without rolling my arches.

 

hope that helps a little.

 

No rolling on the rears with -5, is that with a fair bit of camber and stretch on the tyre?

 

I dont have -5 on the rears or have you quoted the wrong one? As for tyres I run 225/45/18 (front, stretched) 245/45/18 (rear, little stretched)

 

If your et 20 all round and running 25mm spacers on the rear your effectively -5. or have i read that wrong?

[Jared350z]

I dunno as it took me ages to work out the whole ET lark, either way I havent rolled my arches (yet) but My tyres are streched abit at the back but theres still room.

[Jetpilot]

I dunno as it took me ages to work out the whole ET lark, either way I havent rolled my arches (yet) but My tyres are streched abit at the back but theres still room.

 

Although the offset is 20, you have pushed them out a further 25mm by adding the spacers, so effectively making them -5