mr v6

Also how do you reset the auto settings?

http://www.350z-uk.com/topic/158-how-to-window-reset-procedure/

The water isn't collating on the spoiler though, it seems to be running from the vertical seals on the underside of the rear screen.

I didn't have any issues last week on mine & it's th first Z I've done the belts on. You only need to loosen the 14mm nut on the idler enough for it to be adjusted. Is the thread on your adjuster screw corroded with rust which maybe causing an issue?

Is this normal?

It last rained here in Manchester yesterday, just an hour ago I opened the boot & water ran out of what seemed to be a channel behind the outer rear window seal on the inner side of the boot lid skin, causing the water to run out & over the rear 1/4 panel.

If that makes sense?

Where did you order them from?

Got mine from Clark Motorsport on here, but plenty of other places sell it for around the £180 mark. CMS sent mine next day & were awesome to deal with .

I managed to pick up a drivers side one off ebay on Sunday, used of course. It came today & is a genuine Nissan part, fully working, for £65 you can't complain. Will sort the other side out soon.

Galaxy tab4 fits ok in the whole! thats what i've used in mine!

Really? It's a 10" screen & I can't see that fitting inside my cubby hole, it certainly isn't anywhere near 10". In fact after measuring it mine has an internal size of 6x3" roughly.

Cheers Headphones .

Went out an hour ago to fire it up (and annoy the neighbours ) and it's still tick free. All I'm saying is don't jump to conclusions & buy the first part you think you need because you read something on the internet. In my case it was a 5 minute fix.

As I don't want to go out & spend money on a double din head unit with aux inputs, I'd like to add a reverse camera to my Z. I've seen plenty of rear view cameras built into one of the rear reg plate lights, but would prefer to use a dedicated screen I can fit inside the cubby hole.

I'm no stranger to a bit of DIY mechanics, ICE or wiring, so don't mind a 'bit' of a challenge.

Is this something that anyone has done? It's probably a northern thing wanting to save a few quid though .

Since I've had the Z it's always ticked from cold, but fine when totally warmed up. Fuel damper I can hear you all screaming whilst rolling your eyes .

I continued to do the oil change anyway as looking at the partially rusty filter the garage obviously didn't do the job when I asked them before picking it up, then when finished ran the engine & the ticking started as usual. Not totally convinced the fuel damper was my issue I started to feel around. It sounded more like a loud injector pulsing. Starting at cylinder number 1 I pushed down on the top of the coil & silence.. I checked the 10mm coil bolt was tight, it was, I was then sure it was a loose spark plug. Coil off & I must have got around 3/4 turn on the plug. Coil back on & fired her up, silence, no more tapping. I went round & checked all the other coils for any difference in sound & thankfully there isn't.

Maybe a little heads up for those who aren't completely familiar with the Z engine & would rather poke around first before instantly jumping to the first thing you read .

Hi & welcome! My dilemma was between the S2k & the Z.. Common sense told me the Z, I didn't want to drive everywhere at 8000rpm doing 40mph to overtake someone because 'VTEC yo' .

I spend a bit of time in Leeds & pass through Bratford to get there, always on the lookout!

I knew my belts were well past their best when I got the Z. I asked the place to change them, upon collection said they had. What they actually did was just order one belt & leave it in the boot for me .

As I had the belts it's a job I've been meaning to do, so armed only with a 12mm ratchet spanner & a 14mm 3/4" socket with extendable ratchet I set about the job. I did it from above & took probably just under half hour. I know I'd have spent longer than that on my back on the ground fighting with rusty bolts & getting crap in my face.

Old belts:

New belt from the garage is a Continental, the other one I bought is a Gates. I've been out for a quick run & all seems fine, I'll check it tomorrow once the car has cooled overnight & double check the tension.

26 kits left at only £69!

Voucher still on, £79 for forum members.

 

Purchase here: https://www.torqen.u...350z-chclr.html

 

Use: 350zTRQREFL to redeem the discount.

So are they £69 or £79? Mine is 2005, are these the correct ones for my bumper?

I only ask as my Z is due to visit the bodyshop soon, these will be handed to them to fit whilst the front bumper is off..

Very easy to change, however when the bush fails, the arm usually drops down and rests on the lower frame.

This..

I took my Z round to my mechanic today with a replacement bush. He was knocking on 10 mins later saying he'll need to drop part of the rear subframe & to have a look with him. I agreed & left him to it. An hour or so later the Z was back & the fee was £35 for the job & I supplied the part. No more knocking. Oddly the previous owner had replaced the o/s arm with a new one, but I'm northern...

I knew this was coming . Why do you people goad me into buying more bling for my Z? :lol:

My problem is, when I try to undo them with a socket I can feel the resistance, so back it off in the hope it loosens up. Next, it breaks the tab it's sat in on the bumper, that leaves it with nothing for it to bolt to. So I have an undertray that would normally bolt to the holes on the front bumper, but those are now split due to rust.

On another note, I still have the factory front lip.

Thanks Andymac,

Would I be right in saying I retain all of the OEM speakers? If so, aren't I double amplifying the signal? Once from the BOSE amp & again from the head unit?

Thanks to a pheasant, that decided the dart out from a bush today, has caused a good 6" crack on the front bumper & caused quite a bit of crazing in the paint. I'll want the bumper, bonnet, front wings & roof doing.

I'm looking for a recommended paint shop around the Manchester / Warrington / Cheshire area.

Spotted a blue roadster in the Car Hoods workshop this afternoon, I'm guessing it was having work done on the roof.

I've been using Autosmart Reglaze for years, although now replaced by a newer product. 1L bottle, use 25ml of product to roughly 1L of water, meaning you can get 40L of QD for around £12.

All I want to do is a simple oil change. It seems these 10mm bolts in those silly clips are halting me. Just tonight I've loosened a few, but one decided to spin & break the housing it was in. This us now stopping keeping the front lip up, good job I have cable ties.

Not only do I want to do the oil change, at the same time I want to replace both of the drive belts.

Am I missing an obvious trick anywhere?

Thanks everyone. As well as mechanics, this is what I also do in my spare time. I've done a number of Pug 406 Coupes (given I'm Club Secretary on the forum), I've also done the odd Audi, a huuuuge Jag XF that belongs to my sisters fella, amongst others. I like to see an improvement on things.

This was just a quick job. To the untrained eye it'll look awesome. To the trained eye it's a quickie. Upon closer inspection of my wheels, it's clear at some point recently they were refurbed on the cheap. You can seen sloppy paint on the weights & new paint on the old foam from previous weights. I had 2 plans.. Plan A was to have my Touring (I believe they're called) alloys powder coated in a gunmetal or anthracite finish, or buy a used set of Rays & do the same with those & have my tyres put on them.

My bonnet lifters arrived today as TS said they would. All fitted & working perfectly. I would however prefer extra lift on the bonnet. It doesn't seem any different from the standard bonnet stay. Maybe I was spoiled by the generous 406 Coupe lifters where I could get into the engine bay without hitting my head on the underside of the bonnet each time. Instructions were in broken Chinglish & need a Google to fit them, but after a few tweaks all was well.

I've downloaded NDS II (internet search shows this is the version for the Z), it connects to my ELM327 v1.5 adapter, but I see no flashing lights on the adapter. It sees the adapter name & version, but can't see the ECU type & no. Even with auto connect & auto reconnect ticked it just doesn't want to see my Z. Strange, this very adapter works with Torque on the Z & every other car I've plugged it into.

Well the chassis code is definitely KYO. so I'm saying it's Blade Silver, unless someone tells me KYO isn't Blade Silver .

Thanks Randy,

Also for confirming the colour, I thought it was Chrome Silver . During the polish (only a quick hand one) I couldn't help but notice how prominent the metallic flake was on the car, it really does pop in the direct sunlight.