km002916
-
Posts
133 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Store
Posts posted by km002916
-
-
My new ones (this is a trial fit without spigots, centre caps or spacers that I hope to get)
Of course I am biased though
-
raw bhp- does this mean I'd need to purchase shorter studs or do you mean they are easier to cut when you take them out the hub?
Cragus- with regards to the 2nd type (bolt on I assume you mean) do the studs not stick out further than the spacer hence meaning the studs need cut down so as to allow the wheel to sit flush against the spacer?
-
Does fitting 20mm spacers on rear mean you have to cut stud in hub down a bit and if so would 15mm slip ons be a safe bet or is there too little thread left to put nuts on securely?
-
-
thanks Sarah
-
tires look to thin on the back?
i would say 20 or 25mm at the back and 10 or 15mm at the front.
totally agree with you tyre wise, will go for 295/30s when they need replaced rather than 285/20s that are on them just now
-
did trial fitting tonight, didnt look 2 bad without spacers. Think 10mm front and either 15 or 20mm rears would be perfect, opinions?
-
Thanks so much Sarah, deffo 73.1mm that I'm looking for. If you dont please let me know and I'll give Andy a PM as Chris suggested
-
can you sell spiggot rings, I need them for my 350Z for my new Vossen 83s, I believe 73.1 down to 66.1?
-
Does anyone on here sell spiggot rings, I need them for my 350Z for my new Vossen 83s, I believe 73.1 down to 66.1
-
The center bores are the same for the 200SX and 350Z, both 66 so if you have some spacers for the 200, they should work on the Z
Thanks alot for that
-
im checkin theyr same as s14 which seems to be 66
-
Do 350Z have a centre bore of 66?
-
is the centre bore of the 350Z 66?
-
I'm assuming since you're looking at 20 and 25mm spacers you have the wheels and have done the measurements to get the stance you're after?
Not yet, just doing a bit of ground work just now so I know where and what to look for.
-
where these an ebay buy or from someone off the forum?
Was off a Lexus OC forum (I used to have a soarer TT) but purchased and paid for through ebay so if there was any probs I had come back.
-
cheers andlid
The 25mm H&R ones seem to be very commonly used for 200sx s14s through SXOC and driftworks. I've sent a few PMs about them and one for 20mm Keis which are sold by someone recommended on this forum.
Can anyone confirm 100% if 200sx S14/As the same centre bore?
-
with those wheel offstes you'll need 20 on the front and 25 on the back i think
Thanks
-
if your going for spacers i'd get eibachs
any particular reason?
-
200sx s14/a are the same pcd and centre bore aren't they? Found 10mm ones for 50 euro too (would these be enough for the front?)
-
Would H&R hubcentric 25mm spacers do the job, found 2 for £60
-
agreed, the if you tell the seller they wont clear the brakes then they arent the correct fitment for the zed and you could swap them out for something with slightly differnt offsets.
They're used, unfortunetally my finances won't stretch to brand new
What sorta size of spacers, 20 all round?
-
tyres sizes look off too ,fronts ok but rears need to be 30 profile since the Z has a bigger rear rolling radius (most wheel/tyre places arent aware).
edit:
oh and spacers , even if they clear the brembos it will look funny .
get some pics once there on.
I dont ave brembos, I'll see how they look on the car
-
Just bought a set of 20s for the 350 but was wondering if I need to get any spacers or anything or if they'll fit with no problems as stated by the seller?
The front wheels are 20x9 inch with an offset of +35 and tyre is 245/30 R20, the rear wheels are 20x10.5 inch with an offset of +45 and tyre is 285/25 R20.
P.S. I'll reveal what ones and get pics up as soon as I recieve delivery and get them fitted
Post your favourite Zed wheels
in Wheels
Posted
Love the BBS LM-Rs