-
Posts
268 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Store
Posts posted by rm cya
-
-
or just print it off at work??? win win situation.
-
Nismo and Unsilenced decats is where its at!
-
must be. chuck up a pic of your car, lets see if im being a retard but from your sig, you got completely different rims, this guy had grids/gtr's.
-
Still undecided at the mo mate! I reckon I'm going to go 25s as it sits fairly low, and A- I don't want to do any arch work, B- don't want tyre to arch contact.
But 30s look so good!!! FML!!!
-
If you have to break it make sure you wet it! Literally soak it.
-
Haha that looks turd mate! Buy cheap but twice and all that! I got a beastie SnapOn 18v gun. 600ftlb breaking torque
I didn't have to loosen the rear camber bolt. Was enough movement to get it out. Was tight but managed.
Fronts, when pulling the strut out, lean down on the top of the disc and it should be enough movement to pull the strut out.
-
Do you have a battery gun? I managed to buzz it right off without having to use spanners.
And you don't need the 'box spanners'. Normal spanners with the slightly angled ring end work fine.
-
How lean can these engines run with HFCs/decats?
-
thought id whack this up as a how to for people found this video on the tube aswel.
It really is simple. Done mine the other day.
Fronts:
- Remove strutbrace 12mm nuts + bolts (you don't need to loosen the adjustment, just whizz out the mounting bolts)
- remove wheels
- remove lower suspension leg bolt (17mm socket + spanner on other end)
- remove anti rollbar droplink nut - 17mm. Buzz it off with a gun.
- upper wishbone bolts either side of suspension leg - 14mm spanner
- top mount nuts, 3 12mm nuts
- 12mm brake pipe nut
- pull off abs sensor from leg brackets (2)
- Pull suspension leg back a bit to remove the 2 14mm upper wishbone bolts fully.
- Wangle out leg.
- Compress spring
- gun off 17mm top mount nut
- pull off spring
- Fit eibach spring against the seat stops (no need to compress)
- copper grease top mount so it don't creak
- fit top mount
- gun up top mount.
Refit. Remember before you locate the 3 top mount studs back in the strut tower, line up the upper wishbone and slide the bolts in.
Rears:
- Remove wheel
- jack under spring cup
- undo 17mm nut and bolt holding spring cup to hub.
- no need to undo the back bolt.
- lower cup. push down by hand/foot
- remove spring.
- leave the top rubber in place
- remove bottom rubber. Clean + fit to spring against stop
- push down cup/seating arm
- Fit spring
- jack up till hole aligned
- do up 17mm but and bolt.
Job done
- 1
-
I'm an idiot; where does the plate go then?
Passenger footwell
-
Looks sooooooo much better without...
-
pretty sure he had a private plate aswel cant remember it for the life of me though i was in the derv anyways, otherwise they would have heard me and my unsilenced decats paired up to a Nismo
-
Possibly mate! But if you weren't on the A4 down that far there's someone else kicking about local! Exhaust looked stock whereas you got an after market right?
Was heading down from Gilette corner, past PC world towards chiswick direction.
-
About 8.30pm ish, Black Zed, debadged with just a 'Z' in the centre of the boot. Driving down the A4. Think it had Rota Grids or GTRs on it.
-
Brilliant!! Obviously sick of people parking close and denting his doors. But in this case.... Hes been done up the bum.
-
Had to compress mine to remove the stock ones. Couldn't loosen the top mount till pressure was off it. But fitting the Eibach Pro's, didn't need to at all. Top mount flopped on nicely.
-
It really is simple mate. Done mine the other day. Fronts:
- Remove strutbrace 12mm nuts + bolts (you don't need to loosen the adjustment, just whizz out the mounting bolts)
- remove wheels
- remove lower suspension leg bolt (17mm socket + spanner on other end)
- remove anti rollbar droplink nut - 17mm. Buzz it off with a gun.
- upper wishbone bolts either side of suspension leg - 14mm spanner
- top mount nuts, 3 12mm nuts
- 12mm brake pipe nut
- pull off abs sensor from leg brackets (2)
- Pull suspension leg back a bit to remove the 2 14mm upper wishbone bolts fully.
- Wangle out leg.
- Compress spring
- gun off 17mm top mount nut
- pull off spring
- Fit eibach spring against the seat stops (no need to compress)
- copper grease top mount so it don't creak
- fit top mount
- gun up top mount.
Refit.
Rears:
- Remove wheel
- jack under spring cup
- undo 17mm nut and bolt holding spring cup to hub.
- no need to undo the back bolt.
- lower cup. push down by hand/foot
- remove spring.
- leave the top rubber in place
- remove bottom rubber. Clean + fit to spring against stop
- push down cup/seating arm
- Fit spring
- jack up till hole aligned
- do up 17mm but and bolt.
Job done -
Nismo + unsilenced decats.
Still waiting to get an outside vid.
-
Nismo + unsilenced decats.
Still waiting to get an outside vid.
-
I've just fitted the eibach pro kit. Looks amazing but don't want to mess the arches up.
-
I've just fitted the eibach pro kit. Looks amazing but don't want to mess the arches up.
-
Afterthought - what about running a bit of stretch on the stock rays? 30mm looks so good!!
-
Afterthought - what about running a bit of stretch on the stock rays? 30mm looks so good!!
-
You got a pic of the juke satnav?
[SOLD] 2006 Facelift 350Z GT SPEC....UK CAR 300BHP
in Zeds For Sale
Posted
Looks amazing mate!!