All Activity
- Past hour
-
Still not resolved this sluggish power steering issue - it's not the pump, I think it's almost certainly the steering rack, so question is, where do I get a used steering rack?
- Yesterday
-
shooter89 started following 370z behind seat - custom low-profile 6x9 Pods
-
Hi everyone, I wanted to share project I am currently working on for my 370Z. I do not have BOSE and wanted to improve sound quality, so I created these custom 6x9 pods because I wanted a way to mount my Pioneer TS-D69F speakers behind seats. It's slightly tilted not too much, it will sit on the shelf and I will be making small holes on the shelfs for air to escape as it's tiny. I will also install sound insulation in the inside and wrap the outside with speaker cloth. i will be using an amp for these and front door speakers. Let me know what you think, if you have any recommendations?
-
That will be your ABS module. Easily moved to the side to gain access to the master cyl. hardware.
-
All ticket places arw same mate. B@stards. I got into a war with ticket master after stuoidly mixing up venues on a misleading fb weblink. Refused to transfer or refund. If u can find out if the car and holder transfer then i may have it matey. Sorry for delay answering. Things bit manic this end as moving onto a narrowboat.
- Last week
-
There is a bcm or ecu above brake pedal below steering column with bcm caged connection whats this then pls? Thanks for reply btw Bongo
-
cunrah joined the community
-
ZMANALEX started following Clutch master cylinder now! Replacement quide needed help!
-
Just drop the lower trim above the pedals. The 2 bolts and the clevis pin can be reached from there. The ECU will not get in the way as it is on the other side. Top Tip: Bench Bleed the slave and master before fitting.
-
BongoDiv started following Clutch master cylinder now! Replacement quide needed help!
-
Hi Some will recal i droppwd onto a 350z rag top which was standing for 13yrs. Innevitably, now its being used daily issues are arrising lol. I cjanged the slave clutch cylinder after pedal to floor issues and it wont bleed so now purchased a master cylinder. Ive removed all the engine bay pipes and gubins easy enough but cant even see the two 12mm bolts to put a socket on! Do i need to drop the entire pedal box and ecu to gain access? Peed off and missing the drive thrills so please help i wanna get this done and bled tomoz. Back on road asap. Thanks Bongo dave x
-
Turns out master cylinder gone too dammit. Fifty quid ok but total pita to get to bolts in footwell any tips or do i drop pedal box complete?
-
Juan joined the community
-
Jorden joined the community
-
24 IN STOCK
-
SUNDAY BUMP
-
SUNDAY BUMP
-
SUNDAY BUMP
-
SUNDAY BUMP
-
FOR SALE 350Z VQ35DE NEW LOWER SUMP PANS AND SEALER
ZMANALEX replied to ZMANALEX's topic in 350z Parts For Sale
6 IN STOCK -
ATS ACROSS CARBONETIC TWIN PLATE CLUTCH £600.00
ZMANALEX replied to ZMANALEX's topic in 350z Parts For Sale
SUNDAY BUMP -
350Z HR single mass flywheel (SMF) £75.00
ZMANALEX replied to ZMANALEX's topic in 350z Parts For Sale
SUNDAY BUMP -
For Sale: 350Z Rear Wheel Bearing Assembly & Carrier
ZMANALEX replied to ZMANALEX's topic in 350z Parts For Sale
8 IN STOCK -
For Sale: 350Z Rear Wheel Bearing Carrier
ZMANALEX replied to ZMANALEX's topic in 350z Parts For Sale
2 IN STOCK -
For Sale: 350Z Front Wheel Bearing Assembly:
ZMANALEX replied to ZMANALEX's topic in 350z Parts For Sale
6 IN STOCK -
6 IN STOCK
-
FOR SALE NEW ROCKER/CAM COVER ASSEMBLIES 350Z HR
ZMANALEX replied to ZMANALEX's topic in 350z Parts For Sale
1 X SET LEFT IN STOCK. -
FOR SALE NEW ROCKER/CAM COVER ASSEMBLIES VQ35DE
ZMANALEX replied to ZMANALEX's topic in 350z Parts For Sale
3 SETS LEFT IN STOCK