Nismoandy

Hi everyone I have not been on for a while as I have had a few jobs to finish off  I have been running the car when I get a chance so it beds in many components engine clutch etc ,I had my first run out with the club to the Ace cafe , which was a great day out lovely to see many club members. 

One of those jobs was to change over the fuel pump  as the  engine and fuel rail needs to runs at 4 bar around 57psi and the original 350z v6 runs at 3 bar 51psi , although there's not much difference between the pressure it does effect the  start up and the potential power output (bhp)  I'm getting some one to  tune it properly soon ,and  will put on the dino tune for everyone to see. I will  also put on a few more issues that I have had to sort out, soon  

Thanks again Martin for organising this event always a pleasure to meet new members and old friends .

Also very pleased with Steve  Z badge  looks amazing  Photos of the meet 

just a couple of photos of the meet today im no photographer, Andy Muxlow much better can't wait to see his and I had the first drive of the V8Z and I'm pleased to say no problems , lovely to see new members and  old friends 

1) PAYCO - Datsun 510 SSS

2) nismoandy 350z registered & paid

Good news for me I have now got an MOT , but I did have bit of a drama at mot center  , " I arrived on time said hello chatted about the car left the  car running to get the sports cats as warm as possible did the emissions first and all was going well  turned the car off  , then restarted to put on the ramp, and then I had petrol leak from underneath, o dear they were not happy with me, it was were i had clipped on a new hose and it wasn't quite clipped in all the way anyway pushed it back on and all was okay

As soon as It passed I had a quick trip round to a mate of mine. 

their are a few electrical issues so next week it goes in the work shop , nothing to serious 

The very little i have driven it ,it's quite easy to spin up the rear wheels and the stability keeps going off telling me slowly please

Sorry I've double uploaded the same information 

Hi everyone as you can see below I have always dabble with cars, never quite got to finish off the  Lamborghini  , but did the Mercedes 430 clk 

1) Payco - Datsun 510 SSS. Reg WWU 276J

2) KBAD - 350z . Reg J44SUS

3) nismoandy- 350z - WP06FNX 

Is there a way to check that tickets for the previous japfest are still valid and or still recognise by Silverstone? 

Thanks Martin and Andy really appreciated your comments thank you 

Better get some petrol so popped into the local station i probably won't be able to stray to far away from my petrol station    .

got all of this done so thought I'd better get the car out for a bit of a drive, why not  ,what could possibly go wrong 

The exhaust cats are finished and back in now happy with the end result ,also put the w brace back on and a couple of front iner wheel arch liners. 

Hi Paul thanks for that ,good luck with your build but sure you will have few problems with your build as you know what your doing  ,all the best Andy 

I will have to cut and  weld a new 02 sensor hole (bung) as the 02 sensor are read  before the cat and  not after  the cat .

Also I have managed to order the fuel pump and pressure regulator for ls1 engine as it pressure needs to be around 58 psi ,it's from loj conversion and they've managed to incorporate the new fuel pump and pressure regulator in the original  housing as the 350z and also have the same system as Nissan as in a no return fuel line .

So   I've taken the cats apart at the seems made up a new end with 2.5 pipe on it and slid the cats over the top bolt both ends back on ,then tack welded up so as to get the correct positions for both cats 

Above you can see that the exhaust is too low photo below that I disconnected the y pipe from the front part and you can notice that it is lower

Small update it been cold outside in the garage so us southern softy  are rubbish with the cold ,  but I have rehashed the  cats  to lift the exhaust  off the floor.  I have ordered up and received the loj fuel pump and pressure regulator 

Really great, lovely to see the skills that go into this build 

The bodywork is starting to come together i can see that you have spent long hours on your project, hats off to you  keep up your hard  efforts and hope all your problems are tiny one's 

This work looks amazing top quality well done 

40 minutes ago, Stutopia said:

These have arrived and I've packed them for shipping today. There are none left, no spares.

Many thanks for your reply 

1. Stutopia x2

2. Kev T

3. Jack94

4. Harrison140

5. davey83

6. StormtrooperZ

7. andy James x1
8. Andy_Muxlow x1

9. zzIncubus x1

10. ILikeDolphins 

11. NeeZ

12. Ricochet

13. Grumpyoldjanner

14. Flashback x1

15 glrnet

16. Paul K

17. Woodzman

18. MBS x2

19. Lyndzzz

20. da.murf

21. Nismoandy x2