Kestrelone

Not doing any good in the garage. How about £200 for the four with the two tyres?

Good point. They are in Chalfont St Giles, Bucks. Near the M40 and M25 junction

Four Nissan standard fit wheels for the 350Z. Some curbing but not to bad. Fronts are wheels only. Rears have tyres fitted with 4mm tread. Make a good set of winter wheels or pothole damage replacements. Collection only. Asking £250

Tried pasting the image direct and it just rejected every file as being to big. Even though all images had been reduced to lowest file size. Now tried Chrome as suggested and adverts now loaded with moderator! Fingers crossed.

Glad I am not the only one! Will try Chrome instead.

Help. Am I the only one who cannot attach photos to adverts? I am using photobucket as per the instructions. When I get to the polaroid icon it brings up the dialoge box , allows me to paste the image link but then it freezes the page Tried attaching images direct but the lowest quality images get a file to big! Lots to sell but cannot progress

My sons car has a rear disk which is distorted. Brembo brakes fitted. Any suggestions on be replacement disks? Also do the Brembo disks have the hand brake shoes inside the disks ? Not managed to get a look at this yet, probably not till the car arrives for the job.

It's my sons car! Suggested moving the filter up into the under bonnet area for the winter but he is not keen. Problem compounded by the lowered suspension. Maybe have to get a bypass valve from the U.S.

Have heard that. More worried about the filter being submerged when hitting deep puddles, especially at night when often invisible. From that view the intake is on the wrong side, I.e. Gutter side!

I have the cold air intake pipe fitted with the filter cone behind the front bumper and just forward of the offside front wheel. Bit worried about sucking in water from flooded roads and wrecking the engine. Intake pipe bypass valves seem to be available in the USA at reasonable prices but nothing available here ! Anybody have one or know of a supplier

I will take them at that price. With delivery. Later next week will be good as away till then.

Hi. Was about to get from Tarmacsportz at £400 including delivery. They are closed until the 28th but that's not a real problem. What price can you do? Brian

Thanks for that. Berks it is then.

Just been reading various forums and the Berks get better press than Japspeed, so maybe go for them instead. Get it really hot and then see how we go.n

Hmmm, got de cats on at the moment so cannot do that. Have the originals but do not want to keep putting them on for the MOT, hence getting the high flow cats.

Just about to fit high flow cats from Japspeed. Wondering if they are good enough to get through the MOT in December? Anyone had issues with these?

Hi. I have a Sigma alarm and immobiliser fitted. Been having a lot of trouble with the remote which has been refusing to arm or disarm the system . Now found that the remote circuit board must have a dry solder joint, now have packing inside the remote cover putting pressure on the board it works. I have two other remote which do not work. Tried reprograming but no good. The alarm is M30. The remotes are all AC110. But the circuit boards do look different. I have heard that even AC110 remotes work of different frequencies? How can you tell? Anybody an expert on this or know where to go to get a fix?

Certainly would. Just sent you a msg. Brian

Thanks. Supplier had them advertised as fronts but must have been rears. Brian

Just changed the rear roll bar links due to noise. Had the cut off the nuts as they were mega tight. Then went to change the front links and found that the ones supplied have smaller diameter bolts then mine! The supplier says the ones supplied are correct! Anybody know I there are different sizes, maybe the roll bar and lower suspension arm are modified?

Just to close this off. Found a way around the problem so if anybody else has lost a Jap speed 4 inch exhaust bung then here is what to do. I bought a 4 inch bung from Pirhana Products on ebay. The flange of this is slightly smaller than the Jap speed one but can be eased out to make it fit. The centre is completely different so I then drilled out the three welds, removed the centre pipe. Cut three small slot where the welds had been which then allowed a correct size 2 inch centre pipe to be forced into the flange.

I need an exhaust bung, would buy a pair if you have them. As long as its 4 inch I will get them to fit my Japspeed tail pipes.

Lost one exhaust bung... Uxbridge area last weekend. Help... anybody got one they can sell me?

Cleaned all the old gung off before sticking these on by they do not look flat, very wavey in the light. Generally looks cheap.

Hi. Interested if its still available. Brian